Manual DeWalt DW678E T 2 (page 22 of 88) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546599

Zoom out

Zoom in

1/88

en - 5 17

ENGLISH

• Slide the cutter (22) out of its holder.

• Reverse the cutter or replace it.

Always replace both cutters.

• Slide the cutter into the holder. At the rabbeting

side (i.e. the side where the side guard is mounted),

the cutter must be flush with the planing shoe.

• Tighten the three bolts (21).

Fitting the shavings discharge cassette (fig. G)

Although this planer was primarily designed for right-

hand side shavings discharge, it can also be used

for left-hand side shavings discharge.

For right-hand side shavings discharge, the planer

can be used with or wothout the cassette.

The cassette must be used in combination with the

dust extraction adaptor when connecting a vacuum

extractor.

• Push the cassette with its head end (23) into the

right-hand side shavings discharge outlet (24)

until it clicks in place. Please note that the figure

shows the left-hand side of the tool.

For left-hand side shavings discharge, the cassette

must always be used.

When using left-hand side shavings

discharge, always use the dust

extraction adaptor and a vacuum

extractor as described below to prevent

clogging. See fig. G.

• Push the cassette with its head end (23) into the

left-hand side shavings discharge outlet (24) until

it clicks in place.

• Connect the adaptor (25) to a vacuum extractor.

• To remove the cassette, depress the head end (23)

and pull out the cassette.

Instructions for use

Always observe the safety instructions

and applicable regulations.

Prior to operation:

• Adjust the depth of cut.

• If necessary, fit and adjust the parallel fence.

• Attach the shavings discharge cassette.

Use sharp cutters only.

Switching ON and OFF (fig. A)

Your Planer is equipped with a safety switch to

prevent inadvertent operation.

• Switching ON: press the lock-off button (2) and

subsequently press the ON/OFF-switch (1).

• Release the lock-off button (2).

• Switching OFF: release the ON/OFF-switch (1).

Always switch OFF the tool when work is finished

and before unplugging.

Dust extraction

Since woodworking with a planer produces dust,

always install a dustbag or connect a vacuum

extractor designed in compliance with the applicable

Directives regarding dust emission.

Your planer is supplied with an adapter for

connecting a dustbag or a vacuum extractor.

The dustbag is standard for K-models and available

as an option for all other models.

• Attach the dustbag to the shavings discharge

cassette using the adaptor for right-hand side

ejection only.

• Alternatively, for either left-hand or right-hand

side ejection, connect the planer to a vacuum

cleaner using the adaptor (25).

When using left-hand side shavings

discharge, always connect the planer to

a suitable vacuum extractor to prevent

clogging.

Planing (fig. A)

• Switch the tool ON as described.

• Slowly move the Planer over the workpiece.

• The feed speed should not be too high,

especially when using the maximum

depth of cut and planing width.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW678E T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW678E T 2 Manual

Product: