546596

DeWalt DW678 T 3 Manual

21
Zoom out
Zoom in
Previous page
1/88
Next page
ENGLISH
16 en - 4
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Adjusting the depth of cut (fig. B)
• Turn the planing depth adjustment knob (4).
One revolution of the adjustment knob equals
a 4.0 mm change in depth. One graduation
corresponds to a depth of cut of 0.1 mm.
Attaching and removing the parallel fence
(fig. A & C)
The parallel fence (13) is used for optimum tool
control on narrow workpieces.
• Fit the parallel fence (13) to the threaded hole (6)
from either side.
• Tighten the wing bolt (14).
• To remove the parallel fence, proceed in reverse
order.
Attaching, removing and adjusting the rabbeting
depth stop (fig. A)
• Install the depth stop (8).
• Tighten the wing bolt at the desired height in the
threaded hole using the scale.
• To remove the depth stop, proceed in reverse
order.
Attaching and removing the stationary stand
(DE6661) (fig. D & E)
The stationary stand in figure D is the DE6661.
This stand is available as an option as well as the
thicknessing and surfacing stand DE80.
• Open the guard (17) on the stationary stand.
• Place the planer on the stationary stand (15).
• Tighten the star knob (16).
• Attach the parallel fence (13) as described.
• To remove the stationary stand, proceed in
reverse order.
The part of the cutter that is not being
used must always be covered by the
guard (17) or by the parallel fence (13).
Removing reversible cutters (fig. F)
• Loosen the three bolts (21) using the spanner
supplied.
• Flap the side guard (9) up.
• Never use a light socket.
• Never connect the live (L) or neutral (N)
wires to the earth pin marked E or .
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm
2
. When using a cable reel, always
unwind the cable completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW678 T 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW678 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info