546593

DeWalt DW677 T 2 Manual

24
Zoom out
Zoom in
Previous page
1/104
Next page
ENGLISH
22
Attaching and Removing the Parallel
Fence (fi g. 1, 2, 4)
The parallel fence (l) is used for optimum tool control
on narrow workpieces.
1. Slacken the wing bolt (f).
2. Fit the parallel fence (l) in the hole (g) from either
side.
3. Tighten the wing bolt.
4. To remove the parallel fence, proceed in reverse
order.
Removing Reversible Cutters (fi g. 5)
1. Loosen the three bolts (m) with the spanner (n)
supplied.
2. Flap the side guard (h) up.
3. Slide the cutter (o) out of its holder.
4. Reverse the cutter or replace it.
WARNING: Always replace both
cutters.
5. Slide the cutter into the holder. Make sure that
the cutter is flush with the planing shoe (p).
6. Tighten the three bolts (m).
Prior to Operation:
Adjust the depth of cut.
If necessary, fit and adjust the parallel fence.
WARNING: Use sharp cutters only.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Proper Hand Position (fi g. 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (r), with the other hand on the front
handle (d).
Switching On And Off (fi g. 1, 2)
Your planer is equipped with a safety switch to
prevent inadvertent operation.
1. Switching on: press the lock-off button (b) and
subsequently press the on/off switch (a).
2. Release the lock-off button (b).
3. Switching off: release the on/off switch (a).
Always switch off the tool when work is finished and
before unplugging.
Planing (fi g. 1, 2)
1. Switch the tool on as described.
2. Slowly move the planer over the workpiece.
WARNING: The feed speed should
not be too high, especially when using
the maximum depth of cut and planing
width.
NOTE: Remember that several shallow cuts are
better than one deep cut.
3. Switch the tool off.
Your planer is equipped with a parking shoe (k).
After switching off the tool can be put down without
waiting for the cutters to come to a standstill.
Dust Extraction
Whenever possible, connect a dust extraction device
designed in accordance with the relevant regulations
regarding dust emission.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing
set-ups or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can
cause injury.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW677 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW677 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info