546190
27
Zoom out
Zoom in
Previous page
1/108
Next page
ENGLISH
25
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power
input of this tool (see technical data).The minimum
conductor size is 1.5 mm
2
; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Replacing and Centring the Sanding
Belt (fi g. 2, 3)
Your belt sander uses 100 x 570 mm sanding belts.
1. Place the tool on its side with the clamping lever
(l) upwards.
2. Pull the clamping lever (l) upwards and to the
right.
3. Remove the sanding belt (e).
4. Place a new sanding belt making sure that the
arrow on the inside of the sanding belt points in
the same direction as the arrow on the machine
when on the same side of the rollers.
5 Push the clamping lever back.
6. Switch the machine ON and turn the outer belt
centring knob (f) until the sanding belt is centred
on the roller (k).
WARNING: The sanding belt should
never project at the rear! The sanding
belt should be flush with the outer edge
of the sanding surface.
Setting the Electronic Speed Control
Dial (fi g. 1)
DW650E
Turn the speed control dial (b) to the desired
position. The higher the number, the higher the
belt speed.
Dust Extraction
DUSTBAG (FIG. 4)
1. Squeeze the spring (m) of the dustbag (g) and
release it between the fixing rings (n).
2. For efficient dust extraction empty the dustbag
when it is about one third full.
3. Remove the dustbag, open the zipper and
gently shake out the dustbag.
DUST EXTRACTION ADAPTOR
(FIG. 5)
Screw the dust extraction adaptor (h) onto the
outlet (o).
Whenever possible, connect a dust extraction device
designed in accordance with the relevant regulations
regarding dust emission.
WARNING: Do not use a dustbag or
vacuum extractor without proper spark
protection when sanding metal.
WARNING:
Do not sand magnesium!
Do not rough sand pure metal
surfaces.
OPERATION
Instructions for Use
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING:
Always observe the safety
instructions and applicable
regulations.
Make sure all materials to be sanded
are well secured.
Apply only a gentle pressure to the
workpiece.
Sanding (fi g. 1)
A guiding handle (i) has been provided for optimum
tool control when using the Belt Sander without the
stationary stand.
1. Start with the coarsest grit size.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW650 T 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW650 T 6 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 5,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info