546921

DeWalt DW630 Manual

23
Zoom out
Zoom in
Previous page
1/92
Next page
23
E N G L I S H
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
@
Prior to assembly and adjustment
always unplug the tool.
Mounting and removing the sanding disc
(fig. B & D)
● Press the backing pad (6) onto the spindle (5).
● Fit the sanding disc (7) correctly onto the
backing pad.
● Screw the threaded flange (8) onto the spindle
(5).
● Press the spindle lock (4) and rotate the pad
until it locks in position.
● Tighten the threaded flange using the two-pin
spanner (10) supplied.
● Release the spindle lock.
● To remove the sanding disc and backing pad,
loosen the threaded flange using the two-pin
spanner (while the spindle lock is engaged).
Mounting and removing the polishing bonnet
(fig. C & D)
● Press the backing pad (6) onto the spindle (5).
● Screw the threaded flange (8) onto the spindle
(5).
● Press the spindle lock (4) and rotate the pad
until it locks in position.
● Tighten the threaded flange using the two-pin
spanner (10) supplied.
● Release the spindle lock.
● Pull the polishing bonnet (9) over the backing
pad and pull the strings tight. Make a tight knot
and securely push the strings and knot under
the polishing bonnet.
@
Make sure that the strings are covered
completely under the polishing bonnet.
● To remove the polishing bonnet, loosen the knot
and pull the bonnet off the backing pad.
● To remove the backing pad, loosen the
threaded flange using the two-pin spanner
(while the spindle lock is engaged).
Mounting the side handle (fig. E)
● Screw the side handle (3) tightly into one of the
holes (11) on either side of the gear case with
the guard in position to provide optimum
screening.
Instructions for use
@
● Always observe the safety instructions
and applicable regulations.
● Ensure all materials to be sanded or
polished are secured in place.
● Apply only a gentle pressure to the tool.
Do not exert side pressure on the
sanding or polishing accessory.
● Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
● Install the appropriate accessory. Do not use
excessively worn accessories.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW630 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DW630

DeWalt DW630 Additional guide - Polish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info