Manual DeWalt DW62 T 3 (page 26 of 88) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

546203

Zoom out

Zoom in

1/88

ENGLISH

en - 5

• Tighten the locking screw (16).

Removing

• To remove the parallel fence proceed in reverse

order.

Bevel adjustment (fig. C)

The bevel angle can be adjusted between 0° and 45°.

• Slacken the locking screw (15).

• Set the bevel angle by tilting the saw shoe (11).

The angle can be read on the bevel scale (14).

• Tighten the locking screw (15).

Removing and installing the saw blade (fig. D)

• Unplug the tool before proceeding.

• Open the blade guard (8).

• Rotate the saw blade until a screwdriver can be

inserted into the hole in the blade. This will

prevent the blade from rotating while being

loosened.

• If no screwdriver is available, or if the saw blade

used does not have a hole, lock the blade by

pressing the teeth into a piece of wood.

• Loosen and remove the blade bolt (9) and the

washer (23) using the wrench supplied.

• Replace the saw blade. The teeth must point in

the direction of rotation, which is shown by the

arrow on the upper guard housing.

• Reinstall the washer and tighten the blade bolt (9).

Adjusting the riving knife (fig. E)

For the correct adjustment of the riving knife (10),

refer to the inset in figure E. Adjust the clearance of

the riving knife when the saw blade is changed or

whenever necessary.

• Loosen the screw and adjust the clearance as

shown in the inset in fig. E.

• Tighten the screw.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure the material to be sawn is

secured in place.

• Apply only a gentle pressure to the tool

and do not exert side pressure on the

saw blade.

• Avoid overloading.

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

220/240 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Depth of cut adjustment (fig. A)

• Slacken the locking screw (3) and the depth of

cut adjustment (6).

• Set the correct depth of cut. The adjustment can

be read on the scale (13).

• Tighten the depth of cut adjustment and the

locking screw.

For optimal results, allow the saw blade

to protrude from the workpiece by about

3 mm (e.g. for sawing 19 mm thick

board, adjust the depth of cut to

22 mm).

Mounting, adjusting and removing the parallel

fence (fig. B)

The parallel fence (7) is used for cutting parallel to

the edge of the workpiece.

Mounting

• Place the parallel fence (7) on the saw shoe (11).

• Insert the bolt (20) into the hole (21).

• Place the clamping bracket (22) over the bolt and

tighten the locking screw (16).

Adjusting

• Slacken the locking screw (16) and set the

parallel fence (7) to the desired width. The

adjustment can be read on the scale (19).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW62 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW62 T 3 Manual

Product: