546404

DeWalt DW614 T 4 Manual

30
Zoom out
Zoom in
Previous page
1/124
Next page
Proper Hand Position (fi g. A, H)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on each of
the plunge limiters (4).
Switching On and Off (fi g. A)
Switch the tool on using the on/off-switch (1).
I = on. The tool now works continuously.
O = off.
WARNING: Loosen the plunge limiter
and allow the router carriage to regain
its rest position before switching off.
Using the Guide Bushes (fi g. F)
1. Secure the template to the workpiece using end
clamps.
2. Select and install an appropriate guide
bush (18).
3. Subtract the diameter of the cutter from the
outside diameter of the guide bush and divide by
2. This will indicate how much larger the template
should be in relation to the part being recessed.
WARNING: If the workpiece is not thick
enough, place it on a piece of waste
wood.
Guiding Off a Batten
Where an edge guide cannot be used, it is also
possible to guide the router along a batten clamped
across the workpiece (with an overhang at both ends).
Freehand Routing
Your router can also be used without any sort of
guide, e.g. for signwriting or creative work.
WARNING: Make shallow cuts only!
Use cutters with a max. diameter of
6mm.
Routing with Pilot Cutters (fi g. B)
Where a parallel guide or guide bush are
inappropriate, it is possible to use pilot cutters (20)
for cutting shaped edges.
Consult your dealer for further information on the
appropriate accessories.
Adjusting the Parallel Fence (fi g. E)
1. Draw a cutting line on the material.
2. Lower the router carriage until the cutter is in
contact with the workpiece.
3. Tighten the plunge limiter (4).
4. Position the router on the cutting line. The outer
cutting edge of the cutter must coincide with
the cutting line.
5. Slide the parallel fence (16) against the
workpiece and tighten the locking bolts (17).
Fitting a Guide Bush (fi g. F)
Together with a template, guide bushes play a
valuable part in cutting and shaping to a pattern.
1. Fit the guide bush (18) to the router base (11)
using the screws (19) as shown.
WARNING:The screws (19) also hold
the dust extraction channel. Never
operate the router without this.
Connecting a Dust Extractor (fi g. A)
Connect a dust extractor hose to the dust extraction
channel (9).
Prior to Operation
1. Check that the cutter is correctly installed in the
collet.
2. Set the cutting depth.
3. Connect a dust extractor.
4. Always make sure the plunge limiter is locked
before switching ON.
OPERATION
Instructions for use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: Always move your router
as indicated in fig. G (outer edges/inner
edges).
ENGLISH
28
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW614 T 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW614 T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info