Manual DeWalt DW558 (page 23 of 72) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544661

Zoom out

Zoom in

1/72

en - 4

ENGLISH

tool (see technical data). The minimum conductor

size is 1.5 mm

When using a cable reel, always unwind the cable

completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

220/240 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Inserting and removing 19 mm Hex. accessories

(fig. B)

Your DEWALT Demolition Hammer uses accessories

with 19 mm Hex. tool shank (refer to the inset in fig. B

for a cross-section of a chisel shank).

• Grease the chisel shank.

Do not apply bit lubricant to the Power

Tool.

• Push in the tool locking bar (11) and turn it

through 180°.

• Insert the chisel shank into the tool holder (3).

• Push in the tool locking bar and turn it back into

the original position.

• Pull on the chisel to check if it is properly locked.

The hammering function requires the chisel to be

able to move axially several centimetres when

locked in the tool holder.

• Fit the dust cover (12) over the end of the tool

holder (3).

• To remove a chisel push in the tool locking bar (11),

turn it through 180° and pull the chisel out of the

tool holder.

Fitting the side handle (fig. C)

The side handle (4) can be mounted on the front of the

Demolition Hammer to suit both RH- and LH-users.

Always operate the Demolition Hammer

with the side handle properly mounted.

• Unscrew the side handle clamp wheel (5).

• If necessary, remove the side handle mounting

assembly and remount it on the opposite side of

the tool.

• Rotate the mounting assembly to the desired

position.

• Lock the side handle mounting assembly in place

by tightening the clamp wheel (5).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply a pressure of approx. 20 - 30 kg

to the tool. Excessive force does not

speed up chiselling but decreases tool

performance and may shorten tool life.

Demolition, chasing and channelling (fig. A)

• Select the appropriate chisel and grease its shank.

• Insert the chisel and check if it is properly locked.

• Fit the dust cover (12).

• Fit and adjust the side handle (4) and tighten the

side handle clamp wheel (5).

• To run the tool press the ON/OFF-switch (1). The

tool now runs in continuous operation.

• To stop the tool press the locking switch (2)

briefly. Always switch OFF the tool when work is

finished and before unplugging.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW558 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW558 Manual

Product: