Manual DeWalt DW505 T 4 (page 24 of 84) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

544721

Zoom out

Zoom in

1/84

ENGLISH

en - 5 18

DW500/DW505 - Keyed chuck

• Open the chuck by turning the sleeve (9)

counterclockwise and insert the bit shank.

• Put the chuck key (10) into each hole in the side

of the chuck and turn clockwise until tight.

• To remove the bit, proceed in reverse order.

Fitting the side handle (fig. A)

The side handle (6) can be fitted to suit both RH-

and LH-users.

Always use the Drill with the side handle

properly assembled.

• Loosen the side handle.

• For RH-users, slide the side handle clamp over

the collar behind the chuck, handle at the left.

• For LH-users, slide the side handle clamp over

the colar behind the chuck, handle at the right.

• Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (fig. C)

• Insert the required drill bit into the chuck.

• Slacken the side handle (6).

• Fit the depth adjustment rod (7) through the hole

in the side handle clamp.

• Adjust the drilling depth as shown.

• Tighten the side handle.

Forward/reverse slider (fig. A)

• To select forward or reverse rotation, use the

forward/reverse-switch (3) (see arrow on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Two gear selector (fig. D)

This tool is fitted with a two gear selector (4) to vary

the speed/torque ratio.

• Release the ON/OFF-switch and select the

required position as the drill coasts to a stop.

Always align the selector arrow with the gear

symbol on the gear housing:

1 low speed/high torque

(drilling large holes or driving large screws)

2 high speed/low torque

(smaller holes, drilling in wood)

For speed rates, refer to the technical data.

Do not change gears at full speed or

during use.

Chuck removal (fig. E, F & G)

DW241

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw (12) by turning

clockwise.

• Tighten an Allen key into the chuck and strike it

with a hammer as shown.

DW500/DW505

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw (12) by turning

clockwise as shown.

• Insert the chuck key (10) into one of the holes in

the side of the chuck and strike it with a hammer

as shown.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Prior to operation:

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

Switching ON and OFF (fig. A)

• To run the tool, press the variable speed switch.

The pressure exerted on the variable speed

switch determines the tool speed.

Screwdriving

• Select forward or reverse rotation.

• Use the low speed/high torque position

(1st gear).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW505 T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW505 T 4 Manual

Product: