548690
25
Zoom out
Zoom in
Previous page
1/96
Next page
25
Mount the round handle (22) using the two
screws (23).
Fit one screw in the top hole (7) and the other in
one of the side holes (8).
Instructions for use
Always observe the safety instructions
and applicable regulations.
Ensure all materials to be ground or cut
are secured in place.
Apply only a gentle pressure to the tool.
Do not exert side pressure on the
grinding wheel or cutting disc.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
Be sure the spacer and threaded flange are
mounted correctly.
Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and the
tool.
Switching on and off (fig. A)
The on/off-switch of your angle grinder is equipped
with an unlocking switch or a locking switch for
continuous operation.
(U.K. & France only) - On/off-switch (1) with
unlocking switch (2)
To unlock the on/off-switch, slide the unlocking
switch towards you.
To run the tool, press the on/off-switch.
To stop the tool, release the on/off-switch.
On/off-switch (1) with locking switch (2a)
To run the tool, press the on/off-switch. The tool
now runs in continuous operation.
To stop the tool, press the locking switch briefly,
and release the on/off-switch.
Do not switch the tool on or off when
under load.
ENGLISH
DW491 - Using the diamond guard DE8501
(option) (fig. C)
The diamond guard is used for cutting concrete and
masonry, when accurate cutting depth adjustment
or dust extraction are required.
Mount the diamond guard as described above.
Connect a dust extractor to the outlet (17).
Set the cutting depth using the ruler knob in the
front plate (13).
Observe the safety instructions applying
to diamond cutting discs.
Use a suitable diamond cutting disc
(check the data of the manufacturer).
The maximum rotation speed on the cutting
disc must not be lower than that of the tool.
Do not use cutting discs with a diameter
exceeding 230 mm.
Fire hazard! Do not use the dust
extractor when cutting metal!
Make sure that the dust extractor used is
suitable for the material to be cut and the
Diamond guard can be connected.
DW491 - Using the round handle DE8502
(option) (fig. F)
The round handle provides greater convenience and
makes your tool very easy to handle.
Mount the round handle as described above.
Consult your dealer for further information on the
appropriate accessories.
DWLAG.P65 17-09-2001, 08:4925
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW499 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW499 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info