Manual DeWalt DW491 (page 24 of 96) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

447000

Zoom out

Zoom in

1/96

• Remove both screws (12) from the diamond

guard and disassemble the front plate (13).

• Insert the spindle through the hole in the rear

plate (14) and tighten the three screws (10).

Make sure the slots (15) in the rear plate and the

retention disc (16) coincide.

• Rotate the angle grinder to the required position

and tighten the lock nut (11).

• Fit an appropriate diamond cutting disc (see below).

• Mount the front plate (13). Make sure that the dust

extraction outlet (17) is properly caught in the

opening between front (13) and rear plate (14).

Hook the cam behind the ruler stop (18) in the base

plate to make sure the spring (19) can move freely.

• Refit the screws (12).

• To remove the diamond guard, proceed in

reverse order.

Fitting and removing a grinding wheel or cutting

disc (fig. D)

• Place the tool on a table, guard up.

• Fit the spacer (20) correctly onto the spindle (5).

• Place the grinding wheel or cutting disc on the

spacer.

• Screw the threaded flange (21) onto the spindle (5).

• Press the spindle lock (4) and rotate the grinding

wheel or cutting disc until it locks in position.

• Tighten the threaded flange (21) with the two-pin

spanner supplied.

• Release the spindle lock.

• To remove the grinding wheel or cutting disc,

loosen the threaded flange (21) with the two-pin

spanner.

Fitting a wire cup brush

• Screw the wire cup brush directly onto the

spindle without the use of the spacer and

threaded flange.

Mounting the side handle (fig. E)

• For grinding, screw the side handle (6) tightly into

one of the holes (8) on either side of the gear case.

• For cutting, screw the side handle (6) tightly into

the top hole (7).

DW491 + DE8501 - Mounting the round handle

DE8502 (option) (fig. F)

• Remove the side handle.

ENGLISH

Conductor size (mm2) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Voltage drops

Inrush currents cause short-time voltage drops.

Under unfavourable power supply conditions, other

equipment may be affected.

If the system impedance of the power supply is lower

than 0.25 ø, disturbances are unlikely to occur.

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Mounting and removing the guard (fig. B)

• Place the angle grinder on a table, spindle up.

• Mount the guard to the tool using the three

screws (10) with star washers.

• Rotate the guard to the required position and

tighten the lock nut (11).

• To remove the guard, loosen the three screws (10).

DW491 - Mounting and removing the diamond

guard DE8501 (option) (fig. C)

The diamond guard DE8501 has been designed for

depth adjustment and efficient dust extraction.

• Remove the guard from the angle grinder and

place the tool on a table, spindle up.

DWLAG.P65 17-09-2001, 08:4924

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW491 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW491 Manual

Product: