Manual DeWalt DW448 T 1 (page 20 of 82) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

547678

Zoom out

Zoom in

1/82

ENGLISH

en - 5

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

220/240 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Mounting and removing the guard (fig. B & C)

Mounting

• Place the Angle Grinder on a table, spindle up.

• Align the lug (8) with the slot (9) in the bracket.

• Press the guard (5) down and turn it in the

direction of the arrow (fig. B).

The guard locking pin (10) prevents the

guard from coming loose.

Removing

• Hold the tool in your hand.

• Rotate the guard (5) in the direction of the arrow

(fig. C).

• Use a screwdriver to press the locking pin (10) in

the slot.

• Release the guard.

Mounting and removing a grinding wheel or

cutting disk (fig. D & E)

• Place the tool on a table, guard up.

• Fit the spacer (12) correctly onto the spindle (11).

• Place the grinding wheel or cutting disk on the

spacer.

• Screw the threaded flange (13) onto the spindle (11).

• Press the spindle lock (6) and rotate the grinding

wheel or cutting disk until it locks in position.

• Tighten the threaded flange using the two-pin

spanner (14) supplied.

• Release the spindle lock.

• To remove the grinding wheel or cutting disk,

loosen the threaded flange using the two-pin

spanner (while the spindle lock is engaged).

Fitting a wire cup brush

• Screw the wire cup brush directly onto the

spindle without using the spacer and threaded

flange.

Mounting and removing the rubber backing pad

(fig. F)

The rubber backing pad is available as an option.

• Remove the guard from the tool.

• Press the backing pad (16) onto the spindle (11).

The spacer is not needed.

• Position the abrasive disk (15) on the pad.

• Screw the threaded flange (13) onto the spindle (11).

• Press the spindle lock and rotate the pad until it

locks in position.

• Tighten the threaded flange using the two-pin

spanner supplied.

• Release the spindle lock.

• To remove the pad, loosen the threaded flange

using the two-pin spanner (while the spindle lock

is engaged).

Mounting the side handle (fig. H)

• Screw the side handle (4) tightly into one of the

holes (17) on either side of the gear case.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the

grinding wheel or cutting disk.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the appropriate guard and disk or wheel.

Do not use excessively worn disks or wheels.

• Be sure the spacer and threaded flange are

mounted correctly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW448 T 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW448 T 1 Manual

Product: