546678
27
Zoom out
Zoom in
Previous page
1/116
Next page
ENGLISH
25
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in
the plug.
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power
input of this tool (see technical data).The minimum
conductor size is 1.5 mm
2
; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Fitting Sanding Discs (fi g. 2)
Your sander uses 150 mm hook and loop sanding
discs with a 6 hole dust extraction pattern.
1. Place the sander on a table, sanding pad (h) up.
2. Place the sanding disc directly on top of the
sanding pad.
3. Hold the sanding pad (h) with one hand and
align the dust extraction holes (k).
Electronic Speed Control Dial (fi g. 3)
Your sander is equipped with an electronic speed
control dial (b) with 5 positions. Generally, harder
materials require a higher setting. The correct set-
ting, however, is a matter of experience.
FITTING THE SIDE HANDLE (FIG. 4)
1. Remove the plastic screw (o).
2. Mount the side handle (f) on either side of the
tool.
Dust Extraction
Since woodworking with a sander produces dust,
always install the dustbag or connect a vacuum
extractor designed in compliance with the applicable
directives regarding dust emission. Proper dust
extraction will only be achieved with perforated
abrasive.
WARNING: Do not use a dustbag or
vacuum extractor when sanding metal.
WARNING: Do not sand magnesium!
Dustbag (fi g. 1)
Attach the dustbag (c) with the dustbag adaptor (e)
to the dust extraction spout (g). For efficient dust
extraction empty the bag when it is about one third
full.
Vacuum Extractor (fi g. 5)
1. Remove the dustbag adaptor (e) by pulling it
firmly off the dust extraction spout (g).
2. Attach the vacuum extractor adaptor (d) to the
dust extraction spout (g).
3. Connect the vacuum extractor to the vacuum
extractor adaptor (d).
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: Apply only a gentle
pressure to the workpiece. Excessive
pressure does not improve the sanding
effect, but only results in an increased
load on the machine and causes the
abrasive to tear.
WARNING: Avoid overloading.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW443 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW443 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 4,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info