546189

DeWalt DW433 T 2 Manual

27
Zoom out
Zoom in
Previous page
1/116
Next page
ENGLISH
25
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power input
of this tool (see Technical Data).The minimum
conductor size is 1.5 mm
2
; the maximum length
is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Fitting and Centring the Sanding Belt
(fi g. B1, B2)
The tool uses 75 x 533 mm sanding belts.
1. Turn the clamping lever (7) clockwise until it is in
the release position.
2. Remove the sanding belt (10).
3. Place a new sanding belt making sure that the
arrow on the inside of the sanding belt points
in the same direction as the arrow on the
machine.
4. Turn the clamping lever counter-clockwise until
it is in the clamp position.
5. Switch the machine on and turn the belt
centring knob (8) until the sanding belt is
centred on the roller (6).
Adjusting the Front Handle (fi g. C)
The position of the front handle can be adjusted for
optimum control. The default position is on top of
the tool.
1. Loosen the screw (11) located in the centre of
the front handle (3).
2. Take the handle from the socket and place it on
the alternative socket either on top (12) or on
the front (13) of the tool.
3. Make sure that the handle is properly seated.
4. Tighten the screw.
DW433 - Setting the Electronic
Speed Control (fi g. A)
The belt speed is infinitely variable from 260 to
420 m/min using the electronic speed control
dial (5).
Turn the electronic speed control dial to the required
level. The correct setting, however, is a matter of
experience.
Generally, harder materials require a higher setting.
Dust Extraction (fi g. D1, D2)
WARNING: Since woodworking with a
sander produces dust, always install a
dustbag designed in compliance with
the applicable directives regarding dust
emission.
WARNING: Do not use a dustbag or
vacuum extractor without proper spark
protection when sanding metal.
1. Slide the dustbag (9) onto the adaptor (14) over
the edges (15).
2. Pull the locking collar (16) up.
3. Locate the rim (17) behind the edge (18).
4. Align the lugs (19) with the recesses (20).
5. Firmly push the adaptor (14) into the dust
extraction outlet (21) until it clicks in place.
6. Push the locking collar down.
Dust Extraction Shut-off
The dust extraction system can be disabled by
activating the dust extraction shut-off valve. This will
prevent the dust being blown toward the operator.
To close the valve, push the switch (4) forward.
To open the valve, pull the switch backward.
WARNING: While using the dustbag,
always make sure the dust extraction
shut-off valve is open.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW433 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW433 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info