Manual DeWalt DW431 T 5 (page 20 of 80) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546186

Zoom out

Zoom in

1/80

ENGLISH

en - 4 15

• Before replacing the top cover of the mains plug

ensure that the cable restraint(3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

For 115 V units with a power rating exceeding 1500 W,

we recommend to fit a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conductor

size is 1.5 mm

. When using a cable reel, always

unwind the cable completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Fitting and centring the sanding belt (fig. B & C)

Your belt sander uses 75 x 533 mm sanding belts.

• Pull the clamping lever (12) forwards.

• Remove the sanding belt (5).

• Place a new sanding belt making sure that the

arrow on the inside of the sanding belt points in

the same direction as the arrow on the machine

when on the same side of the rollers.

• Push the clamping lever back.

• Switch the machine on and turn the belt centring

knob (6) until the sanding belt is centred on the

roller (10).

DW431 - Speed control (fig. D)

• Turn the speed control dial (2) to the desired

position. The higher the number, the higher the

belt speed.

Mounting, removing and adjusting the sanding

frame (fig. A & E)

The sanding frame is available as an option.

• Remove the locking shaft (13) from the sanding

frame (14) and disassemble the nut, the spring

and the crankshaft (15).

• Push the locking shaft into the hole (11) at the

side where the clamping lever (12) is.

• Mount the spring, the crankshaft and the nut (15).

• Set the crankshafts at right angles with the

sanding belt and push the sanding frame onto

the crankshaft.

• Click the locking shaft (16) into the clamping

spring (4).

• Adjust the height of the sanding frame (14) using

the knob (17).

• To remove the sanding frame, proceed in reverse

order.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW431 T 5 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW431 T 5 Manual

Product: