Manual DeWalt DW411 T1 (page 61 of 64) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546672

Zoom out

Zoom in

1/64

ENGLISH

en - 4

Using an extension cable

If an extension cable is required, use an approved

triple-core extension cable suitable for the power

input of this tool (see technical data). The minimum

conductor size is 1.5 mm

When using a cable reel, always unwind the cable

completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

220/240 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Fitting sanding sheets (fig. B, C & D)

Your DeWALT 1/4 Sheet Sander is designed to use

1/4 sanding sheets (115 x 140 mm).

• Soften the sanding sheet by rubbing its non-

abrasive side over the edge of a worktop (fig. B).

• Unhook both sanding sheet clamp springs (3) as

shown (fig. C).

• Slide the sanding sheet under the sanding sheet

clamp (2) (fig. D).

• Hook the corresponding sanding paper clamp

spring (3) inward and down.

• Stretch the sanding paper firmly over the sanding

pad (4) and repeat for the other clamp.

Fitting the dustbag (fig. E)

• Check that the hatch (7) is open. If not, lift the

notch (8) upward.

• Place the dustbag (6) over the flange (9).

• If no dustbag is used (e.g. when sanding metal),

close the hatch (7).

Since woodworking with a sander produces dust,

always install a dustbag designed in compliance with

the applicable Directives regarding dust emission.

Proper dust extraction will only be achieved with

perforated abrasive.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Make sure all materials to be sanded are

well secured.

• Apply only a gentle pressure to the

workpiece. Excessive pressure does not

improve the sanding effect, but only

results in an increased load on the

machine and causes the sanding sheet

to tear.

Using the hole perforation jig (fig. F)

• Screw the hole perforation jig (10) to a

workbench using the two holes provided for this

purpose.

• Fit a sanding sheet as described above.

• Align the hole perforation jig (10) with the pad (4),

using the four tabs (11).

• Press the jig firmly against the pad to pierce the

holes.

It is also possible to press the hole perforation jig on

the sander base as shown.

Sanding

• Start with the coarsest grit size.

• Move the tool in long sweeping strokes.

• Check your work at short intervals.

Fire hazard! Do not sand magnesium!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW411 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW411 T1 Manual

Product: