546636
27
Zoom out
Zoom in
Previous page
1/120
Next page
ENGLISH
25
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in
the plug.
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power
input of this tool (see technical data).The minimum
conductor size is 1.5 mm
2
; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Fitting the Side Handles (fi g. 2)
1. Put the tool on its side.
2. Carefully insert the top end of one of the side
handles (d) into the opening of the front handle
(c).
3. Turn the side handle until its bottom end
engages in the housing (j).
4. Tighten the fixing screw (m) with the hex key (i).
5. Repeat this procedure for the other side handle.
WARNING: Always operate the
tool with the side handles properly
assembled.
Replacing the Saw Blades
REMOVING THE SAW BLADES (FIG. 3)
1. Turn the tool upside down and remove the saw
blade guard (g).
2. Loosen both saw blade fixing screws (h) with
the hex key (i) until a click is heard.
3. Carefully pull one saw blade until the threaded
hole (n) is out of the housing.
4. Pull the saw blade out of the locking clip (o) and
take it out of the bar (f).
5. Repeat this procedure for the other saw blade.
FITTING THE SAW BLADES (FIG. 4)
1. Slide one saw blade into the bar (f) making sure
its slotted hole (p) fits into the locking clip (o).
2. Insert the back of the saw blade into the
housing (j) until the threaded hole (n) lodges in
the required mounting position.
3. Repeat this procedure for the other saw blade.
4. Using a piece of wood push on the toothed
side of the saw blades to make sure that they
are exactly parallel to the bar (f).
5. Tighten both saw blade fixing screws (h)
securely by pressing and turning simultaneously
with the short end of the Hex key (i).
WARNING: Before operation let the
saw blades run freely for approx. 20 s.
Saw Blades
Material Recommended Cat. #
saw blade
Low density
building block TCT saw blade DT2964
Medium density
building block TCT saw blade DT2966
Cellular concrete TCT saw blade DT2965
Prior to Operation (fi g. 1)
Remove the saw blade guard (g).
Mount the appropriate type of saw blade.
Check that the tool is running properly and can
perform all its functions. Make sure that the bar
(f) is still straight and the saw blades (e) and the
housing (j) are undamaged.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW393 T 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW393 T 5 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info