548880
9
Zoom out
Zoom in
Previous page
1/20
Next page
7
ENGLISH
Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see Technical Data). The minimum conductor
size is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Fitting and Removing 1/4" Hex Drive
Accessories
Your DEWALT screwdriver has a 1/4" hexagonal
drive system. The drive accessory is retained in the
holder by a ball and a spring which engages in a
groove in the accessory shank.
DW268, DW269 (FIG. 1)
1. Pull the ball retainer (e) to the front and hold it.
2. Insert the accessory.
3. Release the ball retainer.
DW266 (FIG. 2)
1. Remove the collar (d) by pulling it forward.
2. Select the required accessory (both models)
and matching depth locator (e) when using a
nutsetter (DW266).
3. To insert the accessory (g), e.g., a bit holder or
nutsetter, push it into the holder (h) until it snaps
in place. Tap it lightly if required.
4. To remove the accessory pull it out of the holder
using a pair of pliers.
5. Reinstall the collar (d) by aligning the ribs (i) on
the inside of the collar (d) with the grooves (j) in
the clutch housing and snap the collar in place.
REPLACING THE BIT TIP (FIG. 2)
Simply pull out the bit tip (k). A pair of pliers maybe
required.
Driving Depth (fi g. 3)
DW266
The depth sensitive feature offers the following
advantages:
The selected driving depth is repeatable for
structural integrity.
Screws with sealing washers are driven correctly
so that no leaks occur.
SETTING THE DRIVING DEPTH
The driving depth is determined by the position of
the depth locator (e) in relation to the bit or socket.
The symbols on the collar (d) indicate how to set the
driving depth.
Turn the collar (d) clockwise to increase the driving
depth.
Turn the collar (d) counterclockwise to decrease the
driving depth.
Using a Nutsetter (fi g. 3)
DW266
1. For screws with sealing washers, turn the collar
(d) until the end of the nutsetter is flush with the
end of the depth locator.
If required, turn the collar until the nutsetter is
recessed approximately 2 mm into the depth
locator.
NOTE: ALWAYS refer to the screw
manufacturer’s specifications for the proper
sealing washer settings in different applications.
2. Drive a screw into a waste piece and check the
distance between the washer and the material.
3. Turn the collar (d) counterclockwise or clockwise
to decrease or increase the driving depth as
required.
4. Drive another screw and readjust the collar (d)
until the desired setting is achieved.
Depth Locator (fi g. 4)
DW266
This model is supplied with two depth locators (e) to
accommodate different bits, holders, sockets and
adaptors.
TO CHANGE DEPTH LOCATORS
1. Pull the collar (d) assembly off the tool.
2. Hold the depth locator (e) and unscrew the
collar (d).
3. Replace the depth locator (e).
To reassemble, proceed in reverse order.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW268K T 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW268K T 5 in the language / languages: English, French as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DW268K T 5

DeWalt DW268K T 5 User Manual - English, German, Dutch, Danish, French, Italian - 120 pages

DeWalt DW268K T 5 Additional guide - Polish - 16 pages

DeWalt DW268K T 5 User Manual - Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info