549014

DeWalt DW263K T 4 Manual

28
Zoom out
Zoom in
Previous page
1/120
Next page
ENGLISH
26
Using a Nutsetter (fi g. 3)
DW263/DW264
1. For screws with sealing washers, turn the collar
(d) until the end of the nutsetter is flush with the
end of the depth locator.
If required, turn the collar until the nutsetter is
recessed approximately 2 mm into the depth
locator.
NOTE: ALWAYS refer to the screw
manufacturer’s specifications for the proper
sealing washer settings in different applications.
2. Drive a screw into a scrap piece and check the
distance between the washer and the material.
3. Turn the collar (d) counterclockwise or clockwise
to decrease or increase the driving depth as
required.
4. Drive another screw and readjust the collar (d)
until the desired setting is achieved.
Depth Locator (fi g. 4)
DW263/DW264
This model is supplied with two depth locators (e) to
accommodate different bits, holders, sockets and
adaptors.
TO CHANGE DEPTH LOCATORS
1. Pull the collar (d) assembly off the tool.
2. Hold the depth locator (e) and unscrew the
collar (d).
3. Replace the depth locator (e).
4. To reassemble, proceed in reverse order.
Forward/Reverse Switch (fi g. 5)
WARNING: Always wait until the motor
has come to a complete standstill
before changing the direction of rotation.
Select the forward or reverse rotation by moving the
forward/reverse switch (c) in the direction indicated
by the arrows.
OPERATION
Instructions for Use
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: Always observe the safety
instructions and applicable regulations.
Proper Hand Position (fi g. 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (n), as shown.
For best results, hold the screwdriver with the
hand directly in line with the fastener and press
the variable speed switch with the last one or
two fingers of the hand, as shown. This reduces
the chance of the screw slipping from the drive
accessory when pressure is applied.
Screwdriving or Nutsetting (fi g. 1A)
1. Select the appropriate bit for the screw (or nut)
to be driven.
2. Select forward or reverse rotation as described
above.
DW263: For nutsetting, always use the correct
depth locator (e).
3. To run the tool, press the variable speed switch
(a). The pressure exerted on the variable speed
switch determines the tool speed.
NOTE: If necessary, press the lock-on button
(b) for continuous operation and release the
variable speed switch. The lock-on button
only works in full speed, forward and reverse
rotation.
To stop the tool in continuous operation, press
the switch briefly and release it.
WARNING: ALWAYS turn the tool
off when work is finished and before
unplugging.
4. To drive the screw, place it on the bit or into
the socket, press the variable speed switch
and push the screw into the workpiece with a
smooth, continuous motion. When the screw
is seated, a buzzing sound will come from the
front of the tool to indicate that the clutch has
disengaged.
5. To stop the tool, release the switch.
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW263K T 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW263K T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 2,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DW263K T 4

DeWalt DW263K T 4 Additional guide - Polish - 16 pages

DeWalt DW263K T 4 Additional guide - Turkish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info