500461

DeWalt DW205C Manual

21
Zoom out
Zoom in
Previous page
1/84
Next page
ENGLISH
16 en - 4
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm
2
. When using a cable reel, always
unwind the cable completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Selecting the operating mode (fig. B)
The tool can be used in two operating modes:
Rotary drilling:
for steel, wood and plastics.
Percussion drilling:
simultaneous rotating and impacting for
concrete and masonry drilling
operations.
• Select the required operating mode by rotating
the mode selector (4) to the required position.
Inserting and removing a bit (fig. A)
DW205C/DW206C - Keyless chuck
• Open the chuck by turning the sleeve (9)
counterclockwise and insert the bit shank.
• Tighten firmly by turning the sleeve clockwise.
DW205/DW206 - Keyed chuck
• Open the chuck by turning the sleeve (9)
counterclockwise and insert the bit shank.
• Put the chuck key (10) into each hole in the side
of the chuck and turn clockwise until tight.
• To remove the bit, proceed in reverse order.
Fitting the side handle (fig. A)
The side handle (6) can be fitted to suit both
RH- and LH-users.
Always use the drill with the side handle
properly assembled.
• Loosen the side handle.
• For RH-users, slide the side handle clamp over
the collar behind the chuck, handle at the left.
• For LH-users, slide the side handle clamp over
the colar behind the chuck, handle at the right.
• Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. C)
• Insert the required drill bit into the chuck.
• Slacken the side handle (6).
• Fit the depth adjustment rod (7) through the hole
in the side handle clamp.
• Adjust the drilling depth as shown.
• Tighten the side handle.
DW205/DW205C - Forward/reverse slider (fig. A)
• To select forward or reverse rotation, use the
forward/reverse-switch (3) (see arrow on tool).
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW205C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW205C in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info