500484
21
Zoom out
Zoom in
Previous page
1/84
Next page
ENGLISH
16 en - 4
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or .
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm
2
. When using a cable reel, always
unwind the cable completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Inserting and removing an accessory (fig. A)
This tool uses morse taper type accessories.
Insert the tapered shank into the tool holder (8).
The accessory will be automatically locked in
position.
To remove the accessory insert the drift wedge (9)
into the drift wedge slot (10) and strike it with a
hammer. The drift wedge can be stored in the
hollow housing of the threaded side handle (6).
Fitting the side handles (fig. B)
The tool is equipped with two removable side
handles (6 & 7) to operate the drill when it is used as
a hand-held tool.
Threaded side handle
Screw the handle (6) into position and tighten it.
Control side handle
Mount the handle (7) onto the gear housing (11)
using the four hexagonal screws (14) provided.
Mounting the breast plate (fig. B)
The breast plate (12) enables optimal control of the
drill when it is used as a hand-held tool.
Mount the breast plate (12) to the rear end of the
tool using the fixing bolt (15) provided.
When using the drill as a hand-held tool
always make sure that the side handles
and breast plate are properly assembled.
Forward/reverse-switch (fig. A)
The forward/reverse action in both gears enables the
tool to be used for e.g. thread tapping.
To select forward or reverse rotation use the
forward/reverse-switch (3).
R (Right) : forward rotation
L (Left) : reverse rotation
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW153 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW153 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info