Manual DeWalt DW056K T 1 (page 30 of 124) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

551270

Zoom out

Zoom in

1/124

ENGLISH

ASSEMBLY

Inserting and removing a bit

(ﬁ g. 1, 4)

DW052, DW054, DW056

The tool uses 1/4" hex. drive system with locking

sleeve.

1. Pull the sleeve/tool holder (c) forward and

insert the bit into the sleeve as far as it will go.

Release the sleeve to secure the bit.

2. To remove the bit, pull sleeve forward and pull

the bit out firmly.

Fitting and removing sockets

(ﬁ g. 1, 4)

DW053, DW055, DW057

The tool uses a 1/2" square drive system with detent

pin.

FITTING SOCKETS

1. Align the hole (j) in the side of the socket with

the detent pin (k) on the anvil.

2. Push the socket (l) onto the anvil/tool holder (c)

until it snaps into place. Tap it lightly if required.

REMOVING SOCKETS

Depress the detent pin (k) through the hole in the

socket and pull the socket off the anvil.

Forward/reverse slider (ﬁ g. 3)

To select forward or reverse rotation, use the

forward/reverse slider (b) as shown (see arrows

on tool).

CAUTION: Always wait until the motor

has come to a complete stand still

before changing the direction of rotation.

The first time the tool is run after changing the

direction of rotation, a click may be heard on

start up.

Instructions for use

WARNING: Always observe the safety

instructions and applicable regulations.

Prior to operation, make sure your battery pack is

(fully) charged.

OPERATION

WARNING: Turn unit off and disconnect

battery pack before installing and

removing accessories, before adjusting

or when making repairs. Lock the trigger

switch when the tool is not in use and

when storing the tool.

Prior to operation

1. Depending on your tool, select the appropriate

bit or socket.

2. To run the tool, press the variable speed switch

(a). The pressure exerted on the variable speed

switch determines the tool speed.

3. To lock the tool in off position, move the

forward/reverse slider (b) to the central position.

To Operate

1. Select forward or reverse rotation using slider

(b).

2. Depending on the application, follow either of

the below instructions.

3. Press the variable speed switch (a).

4. After tightening, check torque with a torque

wrench.

Screwdriving

1. Place the tip of the driver bit in the screw head.

2. Keeping the tool in line with the screw, apply

forward pressure to the tool as it contacts the

work surface.

Nutsetting

1. Place the socket over the head of the bolt or

nut.

2. Hold the tool in line with the fastener.

Tightening time

This tool tightens most fasteners in few seconds.

The proper tightening time in relation to torque must

be determined by experience.

WARNING: Excessive tightening may

damage the tip of the driver bit and the

head of the screw.

Use only dedicated impact accessories with your

tool. Consult your dealer for further information on

the appropriate accessories.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW056K T 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 11,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DW056K T 1

DeWalt DW056K T 1 Additional guide - English - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW056K T 1 Manual

Product: