387230

DeWalt dw 998 k2 Manual

25
Zoom out
Zoom in
Previous page
1/100
Next page
Always release the variable speed switch
and wait until the motor has come to a
complete standstill before changing the
direction of rotation.
Two gear selector (fig. C)
Your tool is fitted with a two gear selector (3) to vary
the speed/torque ratio.
1 low speed/high torque
(drilling large holes or driving large screws)
2 high speed/low torque
(smaller holes, drilling in wood)
For speed rates, refer to the technical data.
Always push the two gear selector
completely forward or completely back.
Do not change gears at full speed or
during use.
Removing and fitting the chuck (fig. E & F)
• Open the chuck jaws as far as possible.
• Tighten an Allen key (14) into the chuck and
strike it with a hammer as shown in figure E.
• Insert a screwdriver into the chuck and remove
the chuck retaining screw by turning clockwise.
• Tighten an Allen key (14) into the chuck and
strike it with a hammer as shown in figure F.
This will loosen the chuck so that it can be
unscrewed by hand.
• To refit the chuck, proceed in reverse order.
Instructions for use
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework and
wiring.
• Apply only a gentle pressure to the tool.
Excessive force does not speed up
drilling but decreases tool performance
and may shorten tool life.
Prior to operation:
• Insert the appropriate bit.
• Mark the spot where the hole is to be drilled.
• Make sure your battery pack is (fully) charged.
• Select forward or reverse rotation.
Switching on and off (fig. A)
• To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed switch
determines the tool speed.
• To stop the tool, release the variable speed
switch (1).
• To lock the tool in OFF-position, move the
forward/reverse slider (2) to the central position.
Screwdriving (fig. C & D)
• Select forward or reverse rotation using the
slider (2).
• Use the low speed/high torque position
(1st gear) (3).
• Set the torque adjustment collar (4). The higher
the number on the collar, the higher the torque
and the larger the fastener which can be driven.
Hammerdrilling (fig. C)
• Select the hammer mode.
• Press the variable speed switch (1).
• To stop the tool, release the switch.
Drilling (fig. C)
• Select the drilling mode.
• Proceed as described for hammerdrilling.
Consult your dealer for further information on the
appropriate accessories.
Maintenance
Your DEWALT Power Tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
• Unplug the charger before cleaning the housing
with a soft cloth.
• Remove the battery pack before cleaning your
Power Tool.
ENGLISH
21 en - 6
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dw 998 k2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 998 k2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info