388587
62
Zoom out
Zoom in
Previous page
1/116
Next page
nl - 5 57
NEDERLANDS
Beschrijving (fig. A)
Uw DEWALT snoerloze schroef-/(klop)boormachine
is ontworpen voor professioneel gebruik.
1 Schakelaar voor elektronisch regelbaar toerental
2 L/R-schakelaar
3 Snelspanboorhouder/automatische
spindelblokkering
4 Instelring voor koppel en boorstand
5 Instelringposities
6 Mechanische toerenomschakelaar
7 Schroefbit-houder
8 Handgreep
9 Accu
Oplader
Uw DE9107 oplader is geschikt voor DEWALT
NiCd-accu’s van 7,2 tot 14,4 V.
Uw DE9108 oplader is geschikt voor DEWALT
NiCd-accu’s van 7,2 tot 18 V.
Uw DE9116 oplader is geschikt voor DEWALT
NiCd- en NiMH-accu’s van 7,2 tot 18 V.
9 Accu
10 Accu-vergrendelingsknoppen
11 Oplader
12 Oplaadindicatie (rood)
Automatische spindelblokkering
De automatische spindelblokkering wordt bij het
uitschakelen van de boormachine geactiveerd.
De kraag kan gemakkelijk met een hand worden
gedraaid terwijl met de andere hand de
boormachine wordt vastgehouden.
Elektrische veiligheid
De elektrische motor is ontwikkeld voor een bepaalde
spanning. Controleer altijd of de accuspanning
overeenkomt met de waarde op het typeplaatje.
Controleer tevens of de ingangsspanning van de
oplader overeenkomt met uw netspanning.
Uw DEWALT-oplader is dubbel
geïsoleerd overeenkomstig EN 50144.
Vervangen van het snoer of de stekker
Als de stekker of het snoer wordt vervangen,
moet de oude stekker c.q. het oude snoer worden
weggegooid. Het is gevaarlijk om de stekker van een
los snoer in het stopcontact te steken.
Gebruik van verlengsnoeren
Gebruik verlengsnoeren alleen in uiterste noodzaak.
Gebruik een goedgekeurd snoer dat beantwoordt
aan het vermogen van de oplader (zie technische
gegevens). De minimum geleiderdikte is 0,5 mm
2
;
de maximum snoerlengte is 30 m.
Monteren en instellen
Verwijder vóór het monteren en instellen
altijd de accu uit de boormachine.
Schakel de machine altijd uit alvorens de
accu aan te brengen of te verwijderen.
Accu (fig. A)
Opladen
Als u de accu voor de eerste keer of na langdurige
opslag oplaadt, zal deze slechts voor ca. 80%
worden opgeladen. Na een aantal laad- en ontlaad-
cycli wordt de accu echter compleet opgeladen.
Controleer altijd de netspanning, voordat u de accu
oplaadt. Als de netspanning normaal aanwezig is,
maar de accu niet wordt opgeladen, breng dan uw
oplader naar een erkend DEWALT Service-center.
Tijdens het opladen kunnen oplader en accu warm
aanvoelen. Dit is normaal en duidt niet op een defect.
Laad de accu niet op bij omgevings-
temperaturen < 4 °C of > 40 °C.
Aanbevolen oplaadtemperatuur: ca. 24 °C.
Plaats de accu (9) in de oplader (11) zoals
weergegeven en steek de stekker van de oplader
in het stopcontact. Let erop dat de accu goed in
de oplader zit. De rode oplaad-indicatie (12) begint
te knipperen. Na ca. 1 uur stopt het knipperen en
brandt de indicatie continu. De accu is nu volledig
opgeladen en de oplader schakelt automatisch
over naar de compensatiestand. Na ongeveer
4 uur schakelt de oplader uiteindelijk naar de
druppellaadstand. De accu kan op elk gewenst
moment uit de oplader worden gehaald of voor
onbepaalde tijd in de op het net aangesloten
oplader worden gelaten.
De rode oplaad-indicatie begint snel te knipperen
als het laden problemen oplevert. Steek de accu
opnieuw in de oplader of probeer een andere
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dw 997 k2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 997 k2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info