Manual DeWalt dw 997 k2 (page 29 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

388587

Zoom out

Zoom in

1/116

ENGLISH

24 en - 7

Removing and fitting the chuck (fig. F & G)

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise

as shown in figure F.

• Tighten an Allen key into the chuck and strike it

with a hammer as shown in figure G. This will

loosen the chuck so that it can be unscrewed

by hand.

• To refit the chuck, proceed in reverse order.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

• To minimise stalling on break-through,

progressively reduce the drill point

pressure towards the end of the

operation.

• Keep the motor running when pulling the

bit back out of a drilled hole. This will

help prevent jamming.

Prior to operation:

• Make sure your battery pack is (fully) charged.

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

• Select forward or reverse rotation.

Switching ON and OFF (fig. A & D)

• To run the tool, press the variable speed switch.

The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in OFF-position, move the

forward/reverse slider (2) to the central position.

The drill is equipped with a brake to stop

the tool as soon as the variable speed

switch is fully released.

Screwdriving (fig. A)

• Select forward or reverse rotation using the

slider (2).

• Set the collar (4) to position 1 and begin

screwdriving (low torque).

• If the clutch ratchets too soon, adjust the collar

to increase the torque as required.

Drilling (fig. A)

• Select the drilling mode using the collar (4).

Drilling in metal

• Use a cutting lubricant when drilling metals.

The exceptions are cast iron and brass which

should be drilled dry.

Drilling in wood

• Holes in wood can be made with the same twist

drills used for metal. These bits may overheat

unless pulled out frequently to clear chips from

the flutes.

• For larger holes use Auger bits.

• Use a block of wood to back up workpieces that

may splinter.

DW909/DW912/DW914/DW997 -

Percussion drilling

Drilling in masonry

• Use carbide-tipped masonry bits up to 10 mm ø

at high speed. Select low speed for larger ø bits.

Keep even force on the drill. A smooth, even flow

of dust indicates the proper drilling rate.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your Power Tool requires no additional lubrication.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 997 k2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dw 997 k2 Manual

Product: