387255
40
Zoom out
Zoom in
Previous page
1/180
Next page
ENGLISH
38
WARNING: Use only DEWALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fi g. A, B)
WARNING: To reduce the risk of
serious personal injury, turn tool off
and disconnect battery pack before
making any adjustments or removing/
installing attachments or accessories.
An accidental start-up can cause injury.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the base of the tool with the notch inside
the tool’s handle (fig. B).
2. Slide the battery pack firmly into the handle until
you hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release buttons (7, fig. A) and firmly
pull the battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
Inserting and Removing Bits (fi g. A)
Open the chuck (4) by turning the sleeve (5)
counterclockwise and insert the bit shank.
Place the bit in the chuck as far as it will go
andlift slightly before tightening.
Tighten firmly by turning the sleeve clockwise
whileholding the rear part of the chuck with one
hand.
To remove the bit, proceed in reverse order.
Forward/reverse Switch (fi g. A)
To select forward or reverse rotation, use the
forward/reverse slider (2) as shown (see arrows
on tool).
WARNING: Always wait until the motor
has come to a complete standstill
before changing the direction of rotation.
Two Gear Selector (fi g. C)
Your tool is fitted with a two gear selector (3) to vary
the speed/torque ratio.
1 low speed/high torque
(drilling large holes, driving screws)
2 high speed/low torque
(drilling smaller holes)
For speed rates, refer to the technical data.
WARNING: Do not change gears at full
speed or during use.
NOTICE:
Always push the two
gear selector completely forward or
backward.
Removing and Fitting the Chuck
(fi g. D, E)
Open the chuck jaws as far as possible.
Insert a screwdriver into the chuck and remove
the chuck retaining screw (12) by turning
clockwise as shown in figure D.
Tighten an Allen key into the chuck and strike
it with a hammer as shown in figure E. This will
loosen the chuck so that it can be unscrewed
by hand.
To refit the chuck, proceed in reverse order.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework and
wiring.
Apply only a gentle pressure to the tool.
Excessive force does not speed up drilling
but decreases tool performance and may
shorten tool life.
To minimise stalling on break-through,
progressively reduce the drill point
pressure towards the end of the
operation.
Keep the motor running when pulling
thebit back out of a drilled hole. This will
help prevent jamming.
PRIOR TO OPERATION
Make sure your battery pack is (fully) charged.
Insert the appropriate bit.
Mark the spot where the hole is to be drilled.
Select forward or reverse rotation.
Proper Hand Position (fi g. F)
WARNING: To reduce the risk of
serious personal injury, ALWAYS
use proper hand position as shown.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dw 960 xj at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 960 xj in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info