390566
36
Zoom out
Zoom in
Previous page
1/164
Next page
34
Prior to Operation
Install the appropriate guard and disk or wheel.
Do not use excessively worn disks or wheels.
Be sure the spacer and threaded flange are
mounted correctly.
Make sure the disk or wheel rotates in the
direction of the arrows on the accessory and the
tool.
Do not use cutting-off wheels for side grinding.
Ensure that sparks resulting from use do not
create hazard e.g. do not hit persons, or ignite
flammable substances.
OPERATION
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
Instructions for Use
WARNING:
Always observe the safety instructions
and applicable regulations.
Ensure all materials to be ground or cut
are secured in place.
Apply only a gentle pressure to the
tool. Do not exert side pressure on the
grinding wheel.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Check that mounted wheels are
correctly fitted according to the
instructions given in this manual.
Ensure that blotters are used when they
are provided with the abrasive wheel
and when they are required.
Do not use separate reducing bushings
or adapters to adapt large hole abrasive
wheels.
Never use the tool without the guard in
place.
Be aware, the wheel continues to rotate
after the tools is switched off.
WARNING:
Ensure all materials to be ground are
secured in place.
Apply only a gentle pressure to the tool.
Do not exert side pressure on the disc.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Proper Hand Position (fi g. H)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side
handle (16), with the other hand on the body of the
tool, as shown in figure H.
Switching On and Off (fi g. G)
WARNING: Before using tool, check that
the handle is tightened securely.
CAUTION: Hold the side handle and
body of the tool firmly to maintain control
of the tool at start up and during use
and until the wheel or accessory stops
rotating. Make sure the wheel has come
to a complete stop be fore laying the tool
down.
To run the tool, press the lock-off button (2) and
the On/Off switch (1).
To stop the tool, release the On/Off switch.
WARNING: Do not switch the tool On or
Off when under load.
Spindle Lock (fi g. A)
The spindle lock (5) is provided to prevent the spindle
from rotating when installing or removing wheels.
Operate the spindle lock only when the tool is turned
off, unplugged from the power supply, and has come
to a complete stop.
NOTICE: To reduce the risk of damage
to the tool, do not engage the spindle
lock while the tool is operating. Damage
to the tool will result and attached
accessory may spin off possibly resulting
in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
ENGLISH
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dw 831 qs at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 831 qs in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 20,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info