Manual DeWalt dw 621 qs (page 25 of 98) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

426996

Zoom out

Zoom in

1/98

20 en - 5

ENGLISH

Adjusting the depth of cut (fig. D)

Your router is equipped with a high precision depth

adjustment system including a zero reset ring for

both the quick adjuster and the fine adjuster.

Quick adjustment using the graduation with zero

reset ring

• Loosen the depth stop locking bolt (14).

• Unlock the plunge limiter (15) by turning it

counterclockwise.

• Lower the router carriage until the cutter is in

contact with the workpiece.

• Tighten the plunge limiter (15).

• Set the quick adjuster (16) to zero using the ring

(22). The depth stop (13) must be in contact with

the revolver depth stop (12).

• Adjust the depth of cut using the quick adjuster (16)

and the corresponding graduation. The adjusted

depth of cut is indicated by the arrows (23).

• Tighten the depth stop locking bolt (14).

Triple depth adjustment using the revolver

depth stop

The revolver depth stop (12) can be used to set

3 different depths. This is particularly useful for deep

cuts, performed in steps.

• Place a depth template between the depth stop

(13) and the revolver depth stop (12) to adjust the

exact cutting depth.

• If required, set all three screws.

Fine adjustment

When not using a depth template, or if the depth of

cut needs readjustment, it is recommended to use

the fine adjuster (17).

• Adjust the depth of cut as described above.

• Set the fine adjuster to zero using the ring (24).

• Rotate the fine adjuster (17) to the required

position: one turn corresponds to approximately

1 mm and 1 mark to 0.1 mm.

Depth adjustment with router installed in inverted

position (fig. D)

• Remove the depth stop (13) and replace it with

the depth stop (DE6956) available as an option.

• Connect the threaded rod of the depth stop

(13A) to the revolver depth stop (12).

• Set the depth of cut using the adjuster on the

depth stop (13A).

For installing the router in inverted

position, refer to the relevant instruction

manual on the stationary tool.

Fitting the parallel fence (fig. A & E)

• Fit the guide rods (5) to the router base (10).

• Tighten the locking bolts (9).

• Slide the parallel fence (8) over the rods.

• Tighten the locking bolts (4) temporarily.

• Remove the dust extraction adaptor (18) and

close the outlet using the dust extraction plug

(25) supplied with the tool.

Adjusting the parallel fence (fig. F)

• Draw a cutting line on the material.

• Lower the router carriage until the cutter is in

contact with the workpiece.

• Tighten the plunge limiter (15).

• Position the router on the cutting line.

• Slide the parallel fence (8) against the workpiece

and tighten the locking bolts (4).

• Adjust the parallel fence (8) using the fine adjuster

(7). The outer cutting edge of the cutter must

coincide with the cutting line.

• Firmly tighten the end lock (20).

Fitting a guide bush (fig. G)

Together with a template, guide bushes play a

valuable part in cutting and shaping to a pattern.

• Fit the guide bush (26) to the router base (10)

using the screws (27) as shown.

Connecting a dust extractor (fig. A & E)

• Connect a dust extractor hose to the dust

extraction adaptor (18) in the router carriage

column, or to the dust extraction outlet in the

parallel fence (6).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Always move your router as indicated in

fig. H (outer edges/inner edges).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 621 qs in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dw 621 qs Manual

Product: