Manual DeWalt dw 615 qs (page 27 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

426924

Zoom out

Zoom in

1/120

Adjusting the Depth of Cut (ﬁ g. D)

DEPTH ADJUSTMENT USING THE GRADUATION AND

REVOLVER DEPTH STOP

1. Loosen the depth stop locking bolt (5).

2 Unlock the plunge limiter (4) by turning it

counterclockwise.

3. Lower the router carriage until the cutter is in

contact with the workpiece.

4. Tighten the plunge limiter (4).

5. Set the exact depth of cut using the graduation

(2) or place a depth template between the depth

stop (3) and the revolver depth stop (6). The

adjustment range is indicated by the arrows (14).

6. Tighten the depth stop locking bolt (5).

TRIPLE DEPTH ADJUSTMENT

The revolver depth stop (6) can be used to set three

different depths. This is particularly useful for deep

cuts, performed in steps.

1. Place a depth template between the depth stop

(3) and the revolver depth stop (6) to adjust the

exact cutting depth.

2. If required, set all three screws.

DEPTH ADJUSTMENT WITH ROUTER INSTALLED IN

INVERTED POSITION

1. Set the depth of cut prior to installing the router

in inverted position.

WARNING: For installing the router in

inverted position, refer to the relevant

instruction manual on the stationary tool.

A fine depth adjuster (DE6956) is available as an

accessory.

Fitting the Parallel Fence (ﬁ g. A, E)

1. Fit the guide rods (15) to the router base (11).

2. Tighten the locking bolts (10).

3. Slide the parallel fence (16) over the rods.

4. Tighten the locking bolts (17) temporarily.

Adjusting the Parallel Fence (ﬁ g. E)

1. Draw a cutting line on the material.

2. Lower the router carriage until the cutter is in

contact with the workpiece.

3. Tighten the plunge limiter (4).

4. Position the router on the cutting line. The outer

cutting edge of the cutter must coincide with

the cutting line.

5. Slide the parallel fence (16) against the

workpiece and tighten the locking bolts (17).

• Slotter cutter with a max shank

diameter of 8 mm and a max diameter

25 mm;

• Grooved knife with a max shank

diameter of 8 mm, a max diameter of

40 mm and a cutting width of 4 mm.

Inserting and Removing a Cutter

(ﬁ g. B)

1. Press and hold down the spindle lock (7).

2. Using the 17 mm wrench, loosen the collet nut

(8) a few turns and insert a cutter.

3. Tighten the collet nut and release the spindle

lock.

WARNING: Never tighten the collet nut

without a cutter in the collet.

Replacing the Collet Assembly

(ﬁ g. C)

Your router is supplied with a 8 mm (GB: 1/4") collet

fitted to the tool. Two other precision collets are also

available to suit the cutter used. The collet and the

collet nut are inseparable.

1. Loosen the collet nut (8) completely.

2. Remove the collet assembly (13).

3. Fit a new assembly and tighten the collet nut (8).

Setting the Electronic Speed Control

Dial (ﬁ g. A)

DW615

The speed is infinitely variable from 8,000 to

24,000 min

-1

using the electronic speed control

dial (12).

1. Turn the electronic speed control dial to the

required level.

2. Generally, use the low setting for large diameter

cutters and the high setting for small diameter

cutters. The correct setting, however, is a matter

of experience.

1 = 8,000 min

-1

2 = 9,500 min

-1

3 = 11,500 min

-1

4 = 16,000 min

-1

5 = 19,500 min

-1

6 = 22,500 min

-1

7 = 24,000 min

-1

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 615 qs in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dw 615 qs Manual

Product: