426922

DeWalt dw 613 Manual

21
Zoom out
Zoom in
Previous page
1/80
Next page
16
ENGLISH
en - 4
Using an extension cable
If an extension cable is required, use an approved
triple-core extension cable suitable for the power
input of this tool (see technical data). The minimum
conductor size is 1.5 mm
2
. When using a cable reel,
always unwind the cable completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
220/240 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Inserting and removing a cutter (fig. B)
• Press and hold down the spindle lock (7).
• Using the 17 mm wrench, loosen the collet nut
(8) a few turns and insert a cutter.
• Tighten the collet nut and release the spindle lock.
Never tighten the collet nut without a
cutter in the collet.
Replacing the collet assembly (fig. C)
Your DEWALT Router is supplied with a 1/4" collet
fitted to the tool. Two other precision collets are also
available to suit the cutter used. The collet and the
collet nut are inseparable.
• Loosen the collet nut (8) completely.
• Remove the collet assembly (13).
• Fit a new assembly and tighten the collet nut.
Adjusting the depth of cut (fig. D)
Depth adjustment using the graduation and
revolver depth stop
• Loosen the depth stop locking bolt (5).
• Unlock the plunge limiter (4) by turning it
counterclockwise.
• Lower the router carriage until the cutter is in
contact with the workpiece.
• Tighten the plunge limiter (4).
• Set the exact depth of cut using the graduation
(2) or place a depth template between the depth
stop (3) and the revolver depth stop (6). The
adjustment range is indicated by the arrows (14).
• Tighten the depth stop locking bolt (5).
Triple depth adjustment
The revolver depth stop (6) can be used to set three
different depths. This is particularly useful for deep
cuts, performed in steps.
• Place a depth template between the depth stop
(3) and the revolver depth stop (6) to adjust the
exact cutting depth.
• If required, set all three screws.
Depth adjustment with Router installed in inverted
position
• Set the depth of cut prior to installing the Router
in inverted position.
For installing the Router in inverted
position, refer to the relevant instruction
manual on the stationary tool. A fine
depth adjuster (DE6906) is available as
an accessory.
Fitting the parallel fence (fig. E)
• Fit the guide rods (15) to the router base (11).
• Tighten the locking bolts (10).
• Slide the parallel fence (16) over the rods.
• Tighten the locking bolts (17) temporarily.
Adjusting the parallel fence (fig. E)
• Draw a cutting line on the material.
• Lower the router carriage until the cutter is in
contact with the workpiece.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dw 613 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 613 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info