Manual DeWalt dw 570 k (page 23 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

388802

Zoom out

Zoom in

1/88

• Mark the spot where the hole is to be drilled.

• Place the drill bit on the spot and press the

variable speed switch (1).

• To stop the tool, release the switch.

Drilling with a core bit (fig. A)

• Set the mode selector (3) to the “hammer drilling”

position.

• Adjust the side handle (4) as required.

• Insert the appropriate core bit.

• Assemble the centerdrill into the core bit.

• Place the centerdrill on the spot and press the

variable speed switch (1). Drill until the core

penetrates into the concrete approx. 1 cm.

• Stop drilling and remove the centerdrill. Place the

core bit back into the hole and continue drilling.

• When drilling through a structure thicker than the

depth of the core bit, break away the round cylinder

of concrete or core inside the bit at regular intervals.

To avoid unwanted breaking away of concrete

around the hole, first drill a hole the diameter of the

centerdrill completely through the structure.

Then drill the cored hole halfway from each side.

Chipping and chiselling (fig. A)

• Before inserting the chisel, set the mode

selector (3) to the “hammering only with

spindle lock” position.

• Insert the appropriate chisel. To adjust the head of

the chisel to the desired angle, set the mode

selector (3) to the “bit rotation” position and rotate

the chisel by hand. Return the mode selector to

the “hammer only with spindle lock” position.

• Adjust the side handle (4) as required.

• Press the variable speed switch (1) and start

working.

• Do not use this tool to mix or pump

easily combustible or explosive fluids

(benzine, alcohol, etc.).

• Do not mix or stir inflammable liquids

labelled accordingly.

Consult your dealer for further information on the

appropriate accessories.

18 en - 5

ENGLISH

Removing and attaching the tool holder (fig. C)

• To remove the tool holder, pull the locking collar

(10) towards the front of the tool and pull the tool

holder off.

• To attach the tool holder, slide the locking collar

towards the SDS-plus

fitting, push the tool holder

onto the spindle, release the locking collar and

rotate the tool holder until it clicks into position.

A keyless 3-jawed chuck for drilling in wood, metal

and plastics is available as an accessory (DT7003).

Please contact your local DEWALT dealer for further

information.

Adjusting the side handle (fig. D)

To adjust the position of the side handle (4):

• Loosen the handle by unscrewing it (A).

• Rotate the handle to the desired position and

tighten it (B).

Always use the tool with the side handle

properly assembled.

Setting the drilling depth (fig. E)

• Insert the required drill bit as described above.

• Loosen the depth stop clamp (6).

• Fit the depth adjustment rod (5) through the hole

in the depth stop clamp.

• Adjust the drilling depth as shown.

• Tighten the depth stop clamp.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Drilling with a solid bit (fig. A)

• Set the mode selector (3) to the desired position:

hammer drilling for masonry, drilling only for

wood, metal and plastic, hammer only for

chipping and chiselling applications.

• Insert the appropriate drill bit.

• Adjust the side handle (4) as required.

• If necessary, set the drilling depth.

I need the SDS end for my dewalt 570 rotory hammer drill to hold my chisel ends is it possible to buy is or is my dewalt rotory hammer drill scrap I believe that's the problem thank you Brian gtmustang 6671 @gmail.com Submitted on 6-3-2023 at 05:21
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 570 k in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dw 570 k Manual

Product: