387207

DeWalt dw 567 k Manual

25
Zoom out
Zoom in
Previous page
1/84
Next page
17
ENGLISH
en - 4
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or .
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
triple-core extension cable suitable for the power
input of this tool (see technical data). The minimum
conductor size is 1.5 mm
2
. When using a cable reel,
always unwind the cable completely. Also refer to
the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Selecting the operating mode (fig. B)
The Rotary Hammer Drill can be used in three
operating modes:
Rotary drilling:
for screwdriving, drilling into steel, wood
and plastics
Hammer drilling:
simultaneous rotating and impacting for
concrete and masonry drilling and
carbide tipped core drilling
Hammering only with spindle lock:
impacting only - for light chipping,
chiselling and demolition applications.
• Select the required operating mode by rotating
the mode selector (4) towards the symbol on the
gear housing.
• For screwdriving, refer to section “Instructions for
use”.
Inserting and removing SDS-plus
®
accessories
(fig. C)
Your Rotary Hammer Drill uses SDS-plus
®
accessories
(refer to the inset in fig. C for a cross-section of an
SDS-plus
®
bit shank).
• Clean and grease the bit shank.
• Insert the bit shank into the tool holder (8).
• Push the bit down and turn it slightly until it fits
into the slots.
• Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
• To remove a bit pull back the tool holder locking
sleeve (9) and pull out the bit.
Fitting the side handle (fig. D)
The side handle (5) can be fitted to suit both RH-
and LH-users.
Always use the tool with the side handle
properly assembled.
• Loosen the side handle.
• For RH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the left.
• For LH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the right.
• Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. E)
• Insert the required drill bit.
• Slacken the side handle (5).
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dw 567 k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 567 k in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info