Manual DeWalt dw 566 k (page 26 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

387206

Zoom out

Zoom in

1/88

ENGLISH

en - 5

• Push the bit down and turn it slightly until it fits

into the slots.

• Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

• To remove a bit pull back the tool holder locking

sleeve (9) and pull out the bit.

Fitting the side handle (fig. D)

The side handle (5) can be fitted to suit both RH-

and LH-users.

Always use the tool with the side handle

properly assembled.

• Loosen the side handle.

• For RH-users, slide the side handle clamp over

the collar behind the tool holder, handle at the

left.

• For LH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the right.

• Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (fig. E)

• Insert the required drill bit.

• Slacken the side handle (5).

• Fit the depth adjustment rod (6) through the hole

in the side handle clamp.

• Adjust the drilling depth as shown.

• Tighten the side handle.

Forward/Reverse-lever (fig. F)

• Push the forward/reverse-lever (3) to the LH-side

for forward (RH) rotation. See arrows on tool.

• Push the forward/reverse-lever (3) to the RH-side

for reverse (LH) rotation.

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Replacing the dust cover (fig. C)

The dust cover (7) prevents dust ingress into the

mechanism. Replace a worn dust cover

immediately.

• Pull back the tool holder locking sleeve (9) and

pull the dust cover (7) off.

• Fit the new dust cover.

• Release the tool holder locking sleeve.

How to fit the Chuck Adapter & Chuck

• Unplug the tool.

• Screw the keyed chuck onto the threaded end of

the chuck adapter.

• Insert the connected chuck and adapter in the

tool as though it were a standard SDS-plus

bit.

• Always tighten the accessory into the keyed

chuck using all three holes.

• To remove the chuck, proceed as for removing a

standard SDS-plus

bit.

• Never use the keyed chuck in hammer

drilling mode.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool

(approx. 2-3 kg). Excessive force does

not speed up drilling but decreases tool

performance and may shorten tool life.

• Do not drill or drive too deep to prevent

damage to the dust cover.

Switching ON and OFF (fig. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed

switch determines the tool speed.

• If necessary, press the lock-on button (2) for

continuous operation and release the variable

speed switch. The lock-on button works only in

full speed, forward rotation.

• To stop the tool, release the variable speed switch.

• To stop the tool in continuous operation, press

the variable speed switch briefly and release it.

Always switch OFF the tool when work is finished

and before unplugging.

Hammer drilling (fig. A)

• Select the hammer drilling mode (4).

• Insert the appropriate SDS-plus

bit. For best

results use high quality carbide-tipped bits.

• Mark the spot where the hole is to be drilled.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 566 k in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dw 566 k Manual

Product: