110216
30
Zoom out
Zoom in
Previous page
1/124
Next page
ENGLISH
28
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Fitting and Removing a Saw Blade
(fi g. 2)
The tool-free blade exchange system ensures quick
and easy changing of saw blades.
1. Open the blade holder (g) by fully retracting the
blade latch (e).
2. Insert the saw blade into the blade holder (g)
guiding the back of the blade into the groove of
the guide roller (h).
3. Release the blade latch (e).
4. To remove the saw blade, fully retract the blade
latch and pull the blade out of the holder.
Setting the Bevel Angle (fi g. 3)
The adjustable shoe (i) allows cutting of LH and RH
bevel angles up to 45°. The bevel scale has preset
positions at 0° and 45°.
1. Slacken the screws (k) using the supplied
wrench.
2. Slide the shoe (i) toward the saw blade.
3. Tilt the shoe and set the desired bevel angle
using the scale.
4. Tighten the screws.
Setting the Pendulum Stroke (fi g. 1)
The adjustable pendulum stroke guarantees a
perfect cutting stroke for different materials.
Slide the selector (j) to the desired position referring
to the table below. The selector can be manipulated
during operation.
Pos. Wood Metal Plastics
2 Fast cuts - PVC
2 Thick workpieces - Fibreglass
Acrylic
1 Plywood Aluminium -
Chipboard Non-ferrous -
0 Thin workpieces Sheet metal -
Fine cuts
Mounting the Plastic Anti-scratch
Shoe Cover (fi g. 4)
The anti-scratch shoe cover (l) reduces damage to
the surface of (sensitive) workpieces.
Click the cover onto the shoe as shown.
Dust Extraction (fi g. 5)
The dust extraction adaptor (m) in combination with
the dust extraction shroud (n) helps extracting the
dust from the workpiece surface, when connected
to a suitable dust extraction system.
1. Place the dust extraction shroud (n) between
the finger guard (f) until it clicks in place.
2. Fit the dust extraction adaptor (m) to the tool as
shown.
3. Connect the hose of a suitable dust extraction
system to the adaptor.
WARNING: When appropriate, connect
a dust extraction system designed
in compliance with the applicable
directives regarding dust emission.
WARNING: Do not use a dust
extraction system without proper spark
protection when sawing metal.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING:
Make sure your workpiece is well
secured. Remove nails, screws and
other fasteners that may damage the
blade.
Check that there is sufficient space for
the blade underneath the workpiece.
Do not cut materials that exceed the
maximum cutting depth of the blade.
Use sharp saw blades only. Damaged
or bent saw blades must be removed
immediately.
Do not use the tool for sawing pipes
or tubes.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW 341 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW 341 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info