Manual DeWalt DW 333 (page 32 of 132) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

110161

Zoom out

Zoom in

1/132

ENGLISH

• For continuous operation, press and hold down

the switch (1), press the lock-on button (2) and

release the switch.

• To stop the tool, release the switch.

• To stop the tool in continuous operation, press

the switch briefly and release it. Always switch

off the tool when work is finished and before

unplugging.

DW333

• Switching on: slide the on/off switch (1) to the front.

• Switching off: slide the on/off switch to the rear.

Always switch off the tool when work is finished

and before unplugging.

Setting the electronic sawing speed

(ﬁ g. G1 & G2)

DW331 (fig. G1)

The sawing speed varies with the pressure exerted

on the on/off switch (1).

• To preset the sawing speed, turn the control dial

(3) to the desired level. The higher the rate, the

higher the sawing speed. The required setting

depends on the thickness and kind of material.

• Use high speeds for sawing soft materials such

as wood. Use low speeds for sawing metal.

DW333 (fig. G2)

The speed control dial (3) can be used for advance

setting of the required range of speed.

• Turn the electronic speed control dial to the

required level. The required setting depends on

the thickness and kind of material.

• Use high speeds for sawing soft materials such

as wood. Use low speeds for sawing metal.

WARNING: After using the tool for

an extended period on low speed

settings, run it for approx. 3 minutes on

maximum no-load speed.

Sawing in wood

• If necessary, draw a cutting line.

• Switch the tool on.

• Hold the tool against the workpiece and follow

the line.

• For sawing parallel to the edge of your workpiece,

install the parallel fence and guide your jigsaw

along the workpiece a shown in figure H.

Sawing in wood using a pilot hole

• If necessary, draw a cutting line.

• Drill a hole (ø min. 12 mm) and introduce the saw

blade.

• Switch the tool on.

• Follow the line.

• For cutting perfectly round shapes, install the

trammel bar and set it to the required radius (fig. I).

Sawing up to a projecting edge (fig. J)

• Using a conventional blade, cut up to the

projected edge.

• Finish off the cut using a flush cutting blade.

Dust extraction (fig. F)

• When the tool is used indoor for extended

periods of time, use a suitable dust extractor

designed in compliance with the applicable

Directives regarding dust emission.

Sawing in metal

• Mount an appropriate saw blade.

• Proceed as described above.

WARNING: Use a cooling lubricant

(cutting oil) to prevent overheating of the

saw blade or the workpiece.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing

set-ups or when making repairs.

Be sure the trigger switch is in the OFF

position. An accidental start-up can

cause injury.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW 333 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW 333 Manual

Product: