Manual DeWalt dw 233 k qs (page 22 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

387243

Zoom out

Zoom in

1/88

en - 5 17

ENGLISH

• Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (fig. B)

• Insert the required drill bit into the chuck.

• Slacken the side handle (5).

• Fit the depth adjustment rod (6) through the hole

in the side handle clamp.

• Adjust the drilling depth as shown.

• Tighten the side handle.

Forward/reverse switch (fig. C)

• To select forward or reverse rotation, use the

forward/reverse-switch (3) as shown

(see arrows on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Two gear selector (fig. D)

Your tool is fitted with a two gear selector (4) to vary

the speed/torque ratio.

• Release the ON/OFF-switch and select the

required position. This can be done with the tool

switched OFF or running under no load

condition. Always align the selector with the

arrow on the gear housing:

1 low speed/high torque

(drilling large holes, driving large screws)

2 high speed/low torque

(drilling smaller holes, drilling in wood)

For speed rates, refer to the technical data.

Do not change gears at full speed or

during use.

Chuck removal (fig. E)

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw (9) by turning clockwise.

• Tighten an Allen key (10) into the chuck and

strike it with a hammer as shown.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Prior to operation:

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

Switching ON and OFF (fig. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed switch

determines the tool speed.

• If necessary, press the lock-on slide (2) upwards

for continuous operation and release the switch.

The lock-on slide works only in full speed,

forward rotation.

• To stop the tool, release the switch.

• To stop the tool in continuous operation,

press the switch briefly and release it.

Always switch OFF the tool when work is finished

and before unplugging.

Screwdriving

• Select forward or reverse rotation.

• Use the low speed/high torque position

(1st gear).

• Do not use this tool to mix or pump

easily combustible or explosive fluids

(benzine, alcohol, etc.).

• Do not mix or stir inflammable liquids

labelled accordingly.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 233 k qs in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dw 233 k qs Manual

Product: