78845
25
Zoom out
Zoom in
Previous page
1/108
Next page
23
ENGLISH
- Alert mode: if the indicator flashes repeatedly,
the electronics do not function properly. Take
your tool to an authorized DEWALT repair agent.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
In case of cord replacement the tool must only
be repaired by an authorized service agent or by
qualifi ed electrician.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the
plug.
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made
to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
WARNING: 115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen between
the primary and secondary winding.
Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conduc tor
size is 1.5 mm
2
. When using a cable reel, always
unwind the cable completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Inserting and Removing a Bit (fi g. A, B)
Open the chuck by turning the sleeve
counterclockwise and insert the bit shank.
Tighten fi rmly by turning the sleeve clockwise.
To remove the bit, proceed in reverse order.
DW221/DW226/DW236/DW246/DW248 -
Spindle Lock
These models have a spindle lock button (4).
Depress the spindle lock button to lock the
chuck while inserting or removing a bit.
WARNING: Never depress the spindle
lock button during operation.
Forward/reverse Slider (fi g. C)
To select forward or reverse rotation, use the
forward/reverse-switch (3) (see arrow on tool).
WARNING: Always wait until the motor
has come to a complete standstill before
changing the direction of rotation.
Chuck Removal (fi g. E & F)
Open the chuck jaws as far as possible.
Insert a screwdriver into the chuck and remove
the chuck retaining screw (8) by turning
clockwise.
Tighten an Allen key into the chuck and strike it
with a hammer as shown.
Prior to Operation
Insert the appropriate bit.
Mark the spot where the hole is to be drilled.
OPERATION
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Instructions for Use
WARNING:
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework
and wiring.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW 226 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW 226 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info