78842
26
Zoom out
Zoom in
Previous page
1/112
Next page
ENGLISH
24
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power
input of this tool (see technical data).The minimum
conductor size is 1.5 mm
2
; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
WARNING: Prior to assembly and
adjustment always unplug the tool.
Inserting and Removing an
Accessory (fi g. 1)
This tool uses morse taper type accessories.
1. Insert the tapered shank into the tool holder (g).
The accessory will be automatically locked in
position.
2. To remove the accessory insert the drift wedge
(h) into the drift wedge slot (i) and strike it with a
hammer. The drift wedge can be stored in the
hollow housing of the threaded side handle (e).
Side Handles (fi g. 2)
The tool is equipped with two removable side
handles (e, f) to operate the drill when it is used as a
hand-held tool.
FITTING THE THREADED SIDE HANDLE
Screw the handle (e) into position and tighten it.
FITTING THE CONTROL SIDE HANDLE
Mount the handle (f) onto the gear housing (j) using
the four hexagonal screws (m) provided.
Mounting the Breast Plate (fi g. 2)
The breast plate (k) enables optimal control of the
drill when it is used as a hand-held tool.
Mount the breast plate (k) to the rear end of the tool
using the fixing bolt (n) provided.
WARNING: When using the drill as a
hand-held tool always make sure that
the side handles and breast plate are
properly assembled.
Forward/reverse Slider (fi g. 1)
The forward/reverse action in both gears enables the
tool to be used for e.g. thread tapping.
To select forward or reverse rotation use the forward/
reverse-switch (b).
– R (Right): forward rotation
– L (Left): reverse rotation
WARNING: The direction of rotation
must only be changed when the motor
has come to a complete standstill. A
safety device prevents any change of
rotation if the motor is still switched on.
Two-gear Selector (fi g. 3)
The tool is fitted with a two gear selector (c) to vary
the speed/torque ratio.
Release the on/off switch and select the
required position after the motor has come to a
complete standstill.
Position Speed/torque ratio Application
I Low speed/high torque Drilling large holes
II High speed/low torque Drilling smaller holes
For speed rates, refer to the technical data.
WARNING: Do not try to change gears
at full speed or under load.
Mounting the drill onto a drill stand. Your drill can be
mounted on a drill stand (optional) for stationary use.
1. Remove the breast plate by loosening the fixing
bolt.
2. Remove both side handles.
3. Mount the tool onto the drill stand. Make sure
to tighten all fixing bolts provided with the drill
stand.
OPERATION
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW 152 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW 152 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info