546574

DeWalt DCS310 T 2 Manual

43
Zoom out
Zoom in
Previous page
1/188
Next page
ENGLISH
41
WARNING: To avoid being pinched,
keep hands away from the hinge when
changing positions.
The tool can be converted into three different
positions. To change positions, slide the pivot
release slider (c) to the right as shown in Figure6
and rotate the handle portion of the tool until it
snaps securely into any of the three positions shown
in Figure 7.
Blade Installation and Removal
(fi g.8, 9A, 9B, 9C)
WARNING: To reduce the risk
of serious personal injury, place
the lock-off button in the lock-
off position or turn tool off and
disconnect battery pack before
making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Different blade lengths are available. Use the
appropriate blade for the application. The blade
should be longer than 3-1/2" (89 mm) and should
extend past the shoe and the thickness of the
workpiece during the cut. A 4" (102 mm) blade is
recommended for best performance. Do not use
jigsaw blades with this tool.
WARNING: Cut hazard. Blade breakage
may occur if the blade does not extend
past the shoe and the workpiece during
the cut (fig.8). Increased risk of personal
injury, as well as damage to the shoe
and workpiece may result.
TO INSTALL BLADE INTO SAW (FIG. 9A, 9B, 9C)
1. Pull blade clamp release lever (g) up.
2. Insert the blade shank into the blade clamp
(f,fig. 9C).
3. Close blade clamp release lever.
4. Note that the blade can be installed upside-
down to assist in flush-to cutting (refer to
fig.9B).
TO REMOVE BLADE FROM SAW (FIG. 9A, 9B, 9C)
CAUTION: Burn hazard. Do not touch
the blade immediately after use. Contact
with the blade may result in personal
injury.
1. Pull blade clamp release lever (g) up.
2. Remove blade.
Worklight (fi g. 9C)
The worklight (e) is located below the blade clamp
(f) behind the shoe. The worklight will be activated
when the trigger switch is squeezed.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Cutting (fi g. 9B, 10–13)
WARNING: Always use eye protection.
All users and bystanders must wear eye
protection that conforms to ANSI Z87.1.
WARNING: Exercise extra caution
when cutting towards operator. Always
hold saw firmly with both hands while
cutting.
Before cutting any type of material, be sure it is firmly
anchored or clamped to prevent slipping. Place
blade lightly against work to be cut, switch on saw
motor and allow it to obtain maximum speed before
applying pressure. Whenever possible, the saw shoe
must be held firmly against the material being cut.
This will prevent the saw from jumping or vibrating
and minimize blade breakage. Any cuts which put
pressure on the blade such as angle or scroll cuts
increase potential for vibration, kickback and blade
breakage.
WARNING: Use extra caution when
cutting overhead and pay particular
attention to overhead wires which may
be hidden from view. Anticipate the path
of falling branches and debris ahead of
time.
WARNING: Inspect work site for hidden
gas pipes, water pipes or electrical wires
before making blind or plunge cuts.
Failure to do so may result in explosion,
property damage, electric shock, and/or
serious personal injury.
FLUSH-TO CUTTING (FIG. 9B, 10)
The compact design of the saw motor housing and
spindle housing permits extremely close cutting to
floors, corners and other difficult areas. The blade
should be inserted upside-down to assist in flush-
cutting (fig.9B).
POCKET/PLUNGE CUTTING – WOOD ONLY (FIG. 11)
The initial step in pocket cutting is to measure the
surface area to be cut and mark clearly with a
pencil, chalk or scriber. Use the appropriate blade
for the application. The blade should be longer than
3-1/2" (89mm) and should extend past the shoe
and the thickness of the workpiece during the cut.
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCS310 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCS310 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 20,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info