551246

DeWalt DCF889 T 2 Manual

38
Zoom out
Zoom in
Previous page
1/168
Next page
ENGLISH
36
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (d).
Variable Speed Trigger Switch (fi g. 1)
To turn the tool on, squeeze the trigger switch
(a). To turn the tool off, release the trigger switch.
Your tool is equipped with a brake. The anvil will
stop when the trigger switch is fully released. The
variable speed switch enables you to select the best
speed for a particular application. The more you
squeeze the trigger, the faster the tool will operate.
For maximum tool life, use variable speed only for
starting holes or fasteners.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(fi g.1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and depress the forward/reverse control button on
the right side of the tool.
To select reverse, release the trigger switch and
depress the forward/reverse control button on the
left side of the tool.
The center position of the control button locks the
tool in the off position. When changing the position
of the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing
the direction of rotation, you may hear a click on
start up. This is normal and does not indicate a
problem.
Worklight (fi g. 1)
There is a worklight (g) located on the foot of the
tool. The worklight is activated when the trigger
switch is depressed. When the trigger is released,
the worklight will stay illuminated for up to 20
seconds.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Anvil (fi g. 2)
WARNING: Use only impact
accessories. Non-impact accessories
may break and cause a hazardous
condition. Inspect accessory prior to
use to ensure that it contains no cracks.
CAUTION: Inspect anvils, detent pins,
and hog rings prior to use. Missing or
damaged items should be replaced
before use.
Place the switch in the locked off (center) position or
remove battery pack before changing accessories.
ANVIL WITH DETENT PIN (FIG. 2)
To install an accessory on the anvil, align the hole in
the side of the accessory with the detent pin (h) on
the anvil (c). Press the accessory on until the detent
pin engages in the hole. Depression of detent pin
may be necessary to aid installation of accessory.
To remove an accessory, depress the detent pin
through the hole and pull the accessory off.
ANVIL WITH HOG RING (FIG. 3)
DCF889H
To install an accessory on the hog ring anvil, firmly
push accessory onto the anvil (c). The hog ring (i)
compresses to allow the accessory to slide on. After
accessory is installed, the hog ring applies pressure
to help provide accessory retention.
To remove an accessory, grasp the accessory and
firmly pull it off.
Usage
Your impact tool can generate the following
maximum torque:
Cat # Nm Ft.-Lbs. In.-Lbs.
DCF889 540 400 4800
DCF889H 540 400 4800
WARNING: Ensure fastener and/
or system will withstand the level
of torque generated by the tool.
Excessive torque may cause
breakage and possible personal
injury.
1. Place the accessory on the fastener head. Keep
the tool pointed straight at the fastener.
2. Press switch to start operation. Release switch
to stop operation. Always check torque with
a torque wrench, as the fastening torque is
affected by many factors including the following:
• Voltage: Low voltage, due to a nearly
discharged battery, will reduce fastening
torque.
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCF889 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCF889 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info