549698
11
Zoom out
Zoom in
Previous page
1/16
Next page
9
NOTE: The worklights are for lighting the immediate work surface and are not
intended to be used as a flashlight.
Quick-Release Chuck (Fig. 2, 4, 5)
DCF815
NOTE: The chuck accepts 1/4" (6.35 mm) hex accessories.
Place the forward/reverse button (B) in the locked off (center) position or remove
battery pack before changing accessories.
FIG. 4
C
D
FIG. 5
C
D
To install an accessory, fully insert the accessory. The accessory is locked into place
(Fig. 4).
To remove an accessory, pull the chuck collar (C) away from the front of the tool.
Remove the accessory and release the collar (Fig. 5).
Anvil with Hog Ring (Fig. 2, 6)
DCF813
CAUTION: Use only impact sockets. Non-impact
J
K
FIG. 6
sockets may break and cause a hazardous condition. Inspect
sock et prior to use to ensure that it con tains no cracks.
Place the forward/reverse button (B) in the locked off (center)
position or remove battery pack before changing accessories.
To install a socket on the hog ring anvil, firmly push socket onto the anvil (J). The
hog ring (K) compresses to allow the socket to slide on. After the socket is installed,
the hog ring applies pressure to help provide socket retention.
To remove a socket, grasp the socket and firmly pull it off.
Usage
Your impact tool generates the following output torque:
Cat # Ft.-Lbs. In.-Lbs. Nm
DCF813-XE 96 1150 130
DCF815-XE 79 950 107
CAUTION: Ensure fastener and/or system will withstand the level of torque
generated by the tool. Excessive torque may cause breakage and possible personal
injury.
1. Place the socket on the fastener head. Keep the tool pointed straight at the
fastener.
2. Press switch to start operation. Always check torque with a torque wrench, as
the fastening torque is affected by many factors including the following:
Voltage: Low voltage, due to a nearly discharged battery, will reduce fastening
torque.
Socket size: Failure to use the correct socket size will cause a reduction in
fastening torque.
Bolt Size: Larger bolt diameters generally require higher fastening torque.
Fastening torque will also vary according to length, grade, and torque
coefficient.
Bolt: Ensure that all threads are free of rust and other debris to allow proper
fastening torque.
Material: The type of material and surface finish of the material will affect
fastening torque.
Fastening Time: Longer fasten ing time results in increased fastening torque.
Using a longer fastening time than recom mended could cause the fasteners to
be overstressed, stripped or damaged.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCF815 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCF815 T 2 in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DCF815 T 2

DeWalt DCF815 T 2 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 156 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info