549690
11
Zoom out
Zoom in
Previous page
1/16
Next page
9
OPERATION
WARNING: To reduce the risk of serious personal injury, turn the tool off and
disconnect the battery pack before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
Installing and Removing the Battery Pack (Fig. 4)
NOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack (G) into the tool handle,
align the battery pack with the recess in the tool’s
handle and slide it into the handle until the battery
pack is firmly seated in the tool and ensure that it does
not disengage.
To remove the battery pack from the tool, press the
release button (F) and firmly pull the battery pack
out of the tool handle. Insert it into the charger as
described in the charger section of this manual.
BATTERY FUEL GAUGE (FIG. 5)
The D
EWALT cordless screwdriver has a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the
battery pack.
To actuate the fuel gauge, press and hold
the motion control activation trigger (A). A
combination of the three green LED lights
will illuminate designating the level of charge
left. When the level of charge in the battery
is below the usable limit, the fuel gauge will
not illuminate and the battery will need to be
recharged.
NOTE: The fuel gauge is only an indication of the charge left on the battery pack.
It does not indicate tool functionality and is subject to variation based on product
components, temperature and end-user application.
FIG. 4
F
G
FIG. 5
A
For more information regarding fuel gauge battery packs, please contact Stanley Black
& Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call 1800 338 002 or (NZ)
0800 339 258.
To Operate
Your screwdriver uses gyroscopic technology to sense your hand motion. To operate,
press in the motion control activation trigger and turn your hand in the direction that
you want the screwdriver to operate.
SETTING INITIAL STARTING POINT
1. Grasp the screwdriver as shown in Figure 6.
2. Press and hold in the motion control activation trigger.
3. When the LED illuminates the tool is ready for use.
4. To reset initial starting point first release the motion control activation trigger.
Move tool to new position, then press and hold in the motion control activation
trigger.
OPERATING IN FORWARD DIRECTION
1. Grasp the screwdriver as shown in Figure 6.
2. Engage head of fastener with screwdriver accessory on work piece. Follow
instructions for setting initial starting point.
3. Rotate your hand to the right and the screwdriver will activate in the forward
direction.
OPERATING IN REVERSE DIRECTION
1. Grasp the screwdriver as shown in Figure 6.
2. Engage head of fastener with screwdriver accessory on work piece. Follow
instructions for setting initial starting point.
3. Rotate your hand to the left and the screwdriver will activate in the reverse
direction.
To turn the tool off, release the motion control activation trigger.
NOTE: When the tool is not in use or during transit please be sure to remove any
accessory from the tool.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCF680 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCF680 T 1 in the language / languages: English as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DCF680 T 1

DeWalt DCF680 T 1 User Manual - English, German, Dutch, Danish, French, Italian - 164 pages

DeWalt DCF680 T 1 Additional guide - Polish - 20 pages

DeWalt DCF680 T 1 User Manual - Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 164 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info