652171

DeWalt DCF620 Manual

39
Zoom out
Zoom in
Previous page
1/172
Next page
37
ENGLISH
You will hear and see the lock on switch return
downwards.
CAUTION: Before using the tool (each
time) be sure that the locking button
release mechanism is working freely. Be
sure to release the locking mechanism
before disconnecting the battery. Failure
to do so will cause the tool to start
immediately the next time the battery is
inserted. Damage or injury could result.
Screwdriving (fi g. 1, 4)
For best results, hold the screwdriver with your
hand directly in line with the fastener and press
the variable speed switch with the last one or two
fingers of the hand. This reduces the chance of
the screw slipping from the drive accessory when
pressure is applied.
To drive the fastener, place it on the bit, press the
variable speed switch and push the fastener into the
workpiece with a smooth, continuous motion. When
the fastener is seated, the clutch will disengage
automatically.
1. Install bit tip in bit holder.
2. Adjust depth locator (a).
3. Check for correct rotation, start screwdriver and
place screw on bit.
4. Contact work surface, applying forward
pressure to drive screw until depth locator
contacts the work surface. Screwgun will
ratchet automatically, disengaging bit from
screw.
5. This depth sensitive screwdriver is suitable for
driving drywall screws.
FOR THIS DEPTH SENSITIVE CLUTCH PLEASE REMEMBER:
• The bit will not turn until pressure is applied to
the unit. Push to engage.
• Trigger switch will not depress unless tool is in
either forward or reverse position.
SCREWDRIVING WITH COLLATED SCREWS (FIG. 5)
To drive collated screws the DCF6201 attachment
should be used. The magazine attachment allows
for faster work flow when driving multiple screws.
Instruction for installation, usage and cleaning of this
attachment is included in the attachment's supplied
manual.
Depth Adjustment
Follow the graphic on the collar to increase or
decrease the fastening depth. To seat the screw
deeper in the workpiece, turn the adjustment
collar to the right. To seat the screw higher in the
workpiece, turn the adjustment collar to the left.
Prior to Operation
1. Make sure your battery pack is (fully) charged.
2. Insert the appropriate drive accessory.
3. Select forward or reverse rotation.
4. Set the appropriate driving depth.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Proper Hand Position (fi g. 4)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the rear
grip. Take care to not block the air vents (x).
Switching On and Off (fi g. 1)
1. To run the tool, press the variable speed switch
(g). The pressure exerted on the variable speed
switch determines the tool speed.
2. To stop the tool, release the variable speed
switch (g).
LOCK ON BUTTON
To lock the trigger switch (g) in the on position for
continuous operation, depress the trigger switch
and push up the lock on button(i). The tool will
continue to run. To turn the tool off, from a locked
on condition, squeeze and release the trigger once.
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCF620 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCF620 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Portuguese, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 23,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info