549687
11
Zoom out
Zoom in
Previous page
1/16
Next page
9
IMPORTANT: When attaching or replacing the belt hook, use only the screw (J) that is
provided. Be sure to securely tighten screw.
The belt hook (F) can be be attached to either side of the tool using only the screw (J)
provided, to accommodate left- or right- handed users. If the hook is not desired at
all, it can be removed from the tool.
To move belt hook, remove the screw (J) that holds the belt hook in place then
reassemble on the opposite side. Be sure to securely tighten screw.
OPERATION
WARNING: To reduce the risk of serious personal injury, place the forward/
reverse button in the lock-off position or turn tool off and disconnect battery pack
before making any adjustments or removing/installing attachments or accessories.
Installing and Removing the Battery Pack (Fig. 3)
NOTE: Make sure your battery pack is fully charged.
To install the battery pack (G) into the tool handle, align the battery pack with the
rails inside the tool’s handle and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
FIG. 3
H
G
To remove the battery pack from the tool, press the release button (H) and firmly pull
the battery pack out of the tool handle. Insert it into the charger as described in the
charger section of this manual.
Variable Speed Switch (Fig. 2)
To turn the tool on, squeeze the trigger switch (A). To turn the tool off, release the
trigger switch. Your tool is equipped with a brake. The chuck will stop when the trigger
switch is fully released.
The variable speed switch enables you to start the application at a slow speed. The
farther you squeeze the trigger, the faster the tool will operate. For maximum tool life,
use variable speed only for starting holes or fasteners.
NOTE: Continuous use in variable speed range is not recommended. It may damage
the switch and should be avoided.
Forward/Reverse Control Button (Fig. 2)
A forward/reverse control button (B) determines the direction of the tool and also
serves as a lock-off button.
To select forward rotation, release the trigger switch and depress the forward/reverse
control button on the right side of the tool.
To select reverse, depress the forward/reverse control button on the left side of the
tool. The centre position of the control button locks the tool in the off position. When
changing the position of the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the direction of rotation, you may
hear a click on start up. This is normal and does not indicate a problem.
Worklights (Fig. 2)
There are three worklights (I) located around the bit holder (D). The worklight will be
activated when the trigger switch is squeezed.
NOTE: The worklight is for lighting the immediate work surface and is not intended to
be used as a flashlight.
Torque Adjustment Collar (Fig. 2)
The torque adjustment collar (C) is clearly marked with numbers and the max
position. The collar should be rotated until the desired setting is located at the top
of the tool. Locators are provided in the collar to eliminate the guess work when
selecting fastening torque. The higher the number on the collar, the higher the
torque and the larger the fastener which can be driven. To lock the clutch for drilling
operations, move to the max position.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCF610 T 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCF610 T 3 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DCF610 T 3

DeWalt DCF610 T 3 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 172 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info