790842

DeWalt DCE089R Manual

11
Zoom out
Zoom in
Previous page
1/126
Next page
11
GB
Maintenance
• To maintain the accuracy of your work, check the laser often
to make sure it is properly calibrated. See Field Calibration
Check.
• Calibration checks and other maintenance repairs may be
performed by DeWALT service centers.
• When not in use, store the laser in the kit box provided. Do
not store your laser at temperatures below -20 ˚C (-5 ˚F ) or
above 60 ˚C (140 ˚F).
• Do not store your laser in the kit box if the laser is wet.
The laser should be dried rst with a soft dry cloth prior to
storage.
Cleaning
Exterior plastic parts may be cleaned with a damp cloth.
Although these parts are solvent resistant, NEVER use
solvents. Use a soft, dry cloth to remove moisture from the tool
before storage.
Accuracy Check and
Calibration
Checking Accuracy –
Horizontal Beam - Scan Direction (See gure 7)
Checking the horizontal scan calibration of the laser requires
two walls 9m (30’) apart. It is important to conduct a calibration
check using a distance no shorter than the distance of the
applications for which the tool will be used.
1. Place the laser on a smooth, at, stable surface that is
level in both directions, with the laser facing straight ahead
toward the opposing wall (0 degree position).
2. Turn on the laser’s horizontal beam and pivot the laser
toward the opposite end of the wall and approximately
parallel to the adjacent wall (Figure 7 #1).
3. Mark the center of the beam at two locations ( a, b) at
least 30’ (9m) apart.
4. Pivot the laser 180 º on the bracket, and mark the horizontal
beam position on the opposing wall c (Figure 7 #2).
5. Measure the vertical distance between b and c. If the
measurement is greater than the values shown below, the
laser must be serviced at an authorized service center.
Distance Between Walls
Allowable Distance
Between b and c
9 m (30’) 6.0 mm (1/4”)
12 m (40’) 8.0 mm (5/16”)
15 m (50’) 10.0 mm (13/32”)
6. Rotate the laser 90 º and repeat the test.
Checking Accuracy –
Horizontal Beam - Pitch Direction (See gure 8)
Checking the horizontal pitch calibration of the laser
requires a single wall at least 30’ (9m) long. It is important
to conduct a calibration check using a distance no shorter
than the distance of the applications for which the tool
will be used.
1. Place the laser on a smooth, at, stable surface that is level
in both directions and against the end of a 30’ (9m) wall.
2. Turn on the laser’s horizontal beam and pivot the laser
toward the opposite end of the wall and approximately
parallel to the adjacent wall (Figure 8 #1).
3. Mark the center of the beam at two locations ( a, b) at
least 30’ (9m) apart.
4. Reposition the laser to the opposite end of the wall (Figure
8 #2).
5. Turn on the laser’s horizontal beam and pivot the laser back
toward the rst end of the wall and approximately parallel to
the adjacent wall.
6. Adjust the height of the laser so that the center of the beam
is aligned with the nearest mark b.
7. Mark the center of the beam c directly above or below the
farthest mark a.
8. Measure the distance between a and c. If the
measurement is greater than the values shown below, the
laser must be serviced at an authorized service center.
Distance Between Walls
Allowable Distance
Between a and c
9 m (30’) 6.0 mm (1/4”)
12 m (40’) 8.0 mm (5/16”)
15 m (50’) 10.0 mm (13/32”)
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCE089R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE089R in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3.67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info