790836

DeWalt DCE0825G Manual

10
Zoom out
Zoom in
Previous page
1/128
Next page
10
GB 4. Check the laser beams. The laser is designed to self-level.
If the laser is tilted so much that it cannot self-level (> 4°),
the laser beam will flash.
• If the laser is tilted between 4° and 10°, the beams will
flash constantly.
• If the laser is tilted greater than 10°, the beams will
continually flash 3 times.
5. If the laser beams ash, the laser is not level (or plumb) and
should NOT BE USED for determining or marking level or
plumb. Try repositioning the laser on a level surface.
6. If ANY of the following statements are TRUE, continue with
the instructions for Checking Laser Accuracy BEFORE
USING THE LASER for a project.
• This is the first time you are using the laser (in case the
laser was exposed to extreme temperatures).
• The laser has not been checked for accuracy in a while.
• The laser may have been dropped.
Checking Laser Accuracy
The laser tools are sealed and calibrated at the factory.
It is recommended that you perform an accuracy check
prior to using the laser for the rst time (in case the laser
was exposed to extreme temperatures) and then regularly to
ensure the accuracy of your work. When performing any of the
accuracy checks listed in this manual, follow these guidelines:
• Use the largest area/distance possible, closest to the
operating distance. The greater the area/distance, the easier
to measure the accuracy of the laser.
• Place the laser on a smooth, at, stable surface that is level
in both directions.
• Mark the center of the laser beam.
Horizontal Line Accuracy - Tilt
Checking the tilt of the laser’s horizontal line requires a at
vertical surface at least 30’ (9m) wide.
1. Place the laser as shown in Figure G #1 and turn the laser
ON.
2. Press 3 times to display a horizontal line and a vertical
line.
3. Aim the laser’s vertical line at the rst corner or reference
point (Figure G #1).
4. Measure half the distance across the wall (D1/2) (Figure G
#1).
5. Where the horizontal laser line crosses the halfway point
(D1/2), mark point P1 (Figure G #1).
6. Rotate the laser to another corner or reference point
(Figure G #2).
7. Where the horizontal laser line crosses the halfway point
(D1/2), mark point P2 (Figure G #2).
8. Measure the vertical distance between P1 and P2 (Figure
G #3).
9. If your measurement is greater than the Allowable
Distance Between P1 & P2 for the corresponding
Distance (D1) in the following table, the laser must be
serviced at an authorized service center.
Distance (D1) Allowable Distance
Between P1 and P2
30’ (9m) 7/32” (5.5mm)
40’ (12m) 9/32” (7.2mm)
50’ (15m) 11/32” (9mm)
Horizontal Line Accuracy - Level
Checking the level of the laser’s horizontal line requires a at
vertical surface at least 30’ (9m) wide.
1. Place the laser at one end of the wall as shown in Figure H
#1, and turn the laser ON.
2. Press once to display a horizontal line.
3. Mark two points (P1 and P2) at least 30’ (9m) apart along
the length of the laser’s horizontal line on the wall (Figure
H #1).
4. Relocate the laser at the other end of the wall and align
the laser’s horizontal line with point P2 (Figure H #2).
5. Mark point P3 on the laser line near point P1 (Figure H
#2).
6. Measure the vertical distance between points P1 and P3
(Figure H #2).
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCE0825G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE0825G in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info