Manual DeWalt DCE0811G (page 10 of 126) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

790843

Zoom out

Zoom in

1/126

GB batteries; see Out of Tilt Range Indicator.) If all 4 LEDs on the

battery meter LEDs continuously ash this does not indicate

a low battery; see “The Battery Meter LEDs Flash” under

Troubleshooting.

Operation

To Turn the Lasers On and Off

(See Figure 1)

With the laser off, place it on a at level surface. Slide the

Pendulum Lock switch B to the Unlocked/ON position. The

DCE089G/R model has three ON/OFF buttons on the keypad

C one for a horizontal laser line D, one for a side vertical laser

line E and one for a front vertical laser line F (DCE089G/R

only). The DCE0811G/R has two lines -a horizontal line and

side vertical line. Each laser line is powered on by pressing its

ON/OFF button on the keypad. The laser lines can be powered

one at a time or all at the same time. Pressing the ON/OFF

keys again turns the laser lines off. Slide the Pendulum Lock

switch to the OFF/Locked position when the laser is not in use.

If the pendulum lock switch is not placed in the lock position all

4 LEDs will continuously ash on the Battery Meter.

Using the Lasers

Out of LEVEL Range Indicator

The lasers are designed to self-level. If the laser has been tilted

so much that it cannot self-level (> 4° ), the laser beam will

ash. There are two ashing sequences associated with the out

of level condition: (i) between 4° and 10° the beams ash with

a constant blink cycle; (ii) at angles greater than 10° the beams

ash with a three blink cycle. When the beams ash THE

LASER IS NOT LEVEL (OR PLUMB) AND SHOULD NOT BE

USED FOR DETERMINING OR MARKING LEVEL OR PLUMB.

Try repositioning the laser on a more level surface.

Using the Pivot Bracket (See gure 2)

WARNING:

Position the laser and/or wall mount on a stable

surface. Serious personal injury or damage to the

laser may result if the laser falls.:

The laser has a magnetic pivot bracket G permanently

attached to the unit. This bracket allows the unit to be mounted

to any upright surface made of steel or iron. Common examples

of suitable surfaces include steel framing studs, steel door

frames and structural steel beams. The bracket also has

a keyhole slot H allowing the unit to be hung from a nail or

screw on any kind of surface.

Using the Laser with the CEILING Mount

(See Figure 5 )

The laser ceiling mount L (if included) offers more mounting

options for the laser. The ceiling mount has a clamp K at

one end which can be xed to a wall angle for acoustic ceiling

installation. At each end of the ceiling mount is a screw hole M

, allowing the ceiling mount to be attached to any surface with

a nail or screw. Once the ceiling mount is secured, its steel plate

provides a surface to which the magnetic pivot bracket G can

be attached. The position of the laser can then be ne-tuned by

sliding the magnetic pivot bracket up or down on the wall mount.

Using the Lasers with Accessories

The lasers are equipped with 1/4” - 20 and 5/8” - 11

female threads on the bottom of the unit. This thread is to

accommodate current or future DeWALT accessories. Only use

DeWALT accessories specied for use with this product. Follow

the directions included with the accessory.

CAUTION:

The use of any other accessory not recommended for

use with this tool could be hazardous.

If you need any assistance in locating any accessory, please

contact your nearest DeWALT service center or go to

www.2helpU.com on the Internet.

Leveling the Lasers

As long as the laser is properly calibrated, the laser is self-

leveling. Each laser is calibrated at the factory to nd level as

long as it is positioned on a at surface within average ± 4° of

level. No manual adjustments are required.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE0811G in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3.67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DCE0811G Manual

Product: