Manual DeWalt DCD771 T 10 (page 43 of 192) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

549605

Zoom out

Zoom in

1/192

ENGLISH

released, the worklight will stay illuminated for up to

20 seconds.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Keyless Single Sleeve Chuck

(fig. 7–9)

WARNING: Do not attempt to tighten

drill bits (or any other accessory) by

gripping the front part of the chuck

and turning the tool on. Damage to

the chuck and personal injury may

result. Always lock off trigger switch

and disconnect tool from power source

when changing acces sories.

WARNING: Always ensure the bit

is secure before starting the tool. A

loose bit may eject from tool causing

possible personal injury.

Your tool features a keyless chuck (f) with one

rotating sleeve for one-handed operation of the

chuck. To insert a drill bit or other accessory, follow

these steps.

1. Turn tool off and disconnect tool from power

source.

2. Grasp the black sleeve of the chuck with one

hand and use the other hand to secure the

tool. Rotate the sleeve counterclockwise far

enough to accept the desired accessory.

3. Insert the accessory about 19 mm (3/4") into

the chuck and tighten securely by rotating

the chuck sleeve clockwise with one hand

while holding the tool with the other. Your tool

is equipped with an automatic spindle lock

mechanism. This allows you to open and close

the chuck with one hand.

Be sure to tighten chuck with one hand on the

chuck sleeve and one hand holding the tool for

maximum tightness.

To release the accessory, repeat steps 1 and 2

above.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

Proper Hand Position (fig. 3)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the top

of the drill as shown, with the other hand on the

main handle (i).

Screwdriver Operation (fig. 4)

1. Select the desired speed/torque range using the

dual range gear selector to match the speed

and torque of the planned operation.

2. Turn the torque adjustment collar (c) to the

desired position. Lower numbers indicate lower

torque settings; higher numbers indicate higher

torque settings.

3. Insert the desired fastener accessory into the

chuck as you would any drill bit.

4. Make some practice runs in scrap or on unseen

areas to determine the proper position of the

clutch collar.

5. Always start with lower torque settings, then

advance to higher torque settings to avoid

damage to the workpiece or fastener.

Drill Operation (fig. 5)

WARNING: To reduce the risk of

serious personal injury, turn tool off and

disconnect tool from power source

before making any adjustments or

removing/installing attachments or

accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped

firmly. If drilling thin material, use a wood

“back-up” block to prevent damage to

the material.

1. Turn the collar (c) to the drill symbol.

2. Select the desired speed/torque range using the

gear shifter to match the speed and torque to

the planned operation.

3. For WOOD, use twist bits, spade bits, power

auger bits or hole saws. For METAL, use high-

speed steel twist drill bits or hole saws. Use

a cutting lubricant when drilling metals. The

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCD771 T 10 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 19,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DCD771 T 10 Manual

Product: