549241

DeWalt DCD735 T 1 Manual

43
Zoom out
Zoom in
Previous page
1/196
Next page
ENGLISH
41
Dual Range Gearing (fi g. 1)
The dual range feature of your drill/driver allows you
to shift gears for greater versatility.
1. To select speed 1 (high torque setting), turn
the tool off and permit it to stop. Slide the gear
shifter (d) forward (towards the chuck).
2. To select speed 2 (low torque setting), turn the
tool off and permit it to stop. Slide the gear
shifter back (away from the chuck).
NOTE: Do not change gears when the tool is
running. Always allow the drill to come to a complete
stop before changing gears. If you are having trouble
changing gears, make sure that the dual range
gear shifter is either completely pushed forward or
completely pushed back.
Worklight (fi g. 1)
There is a worklight (e) located just above the trigger
switch (a). The worklight is activated when the trigger
switch is depressed, and will automatically turn off
20 seconds after the trigger switch is released. If the
trigger switch remains depressed, the worklight will
remain on.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Keyless Single Sleeve Chuck
(fi g. 7–9)
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the front part of the chuck
and turning the tool on. Damage to
the chuck and personal injury may
result. Always lock off trigger switch
and disconnect tool from power source
when changing acces sories.
WARNING: Always ensure the bit
is secure before starting the tool. A
loose bit may eject from tool causing
possible personal injury.
Your tool features a keyless chuck (f) with one
rotating sleeve for one-handed operation of the
chuck. To insert a drill bit or other accessory, follow
these steps.
1. Turn tool off and disconnect tool from power
source.
2. Grasp the black sleeve of the chuck with one
hand and use the other hand to secure the
tool. Rotate the sleeve counterclockwise far
enough to accept the desired accessory.
3. Insert the accessory about 19 mm (3/4") into
the chuck and tighten securely by rotating
the chuck sleeve clockwise with one hand
while holding the tool with the other. Your tool
is equipped with an automatic spindle lock
mechanism. This allows you to open and close
the chuck with one hand.
Be sure to tighten chuck with one hand on the
chuck sleeve and one hand holding the tool for
maximum tightness.
To release the accessory, repeat steps 1 and 2
above.
Belt Hook and Bit Clip (fi g. 1)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
WARNING: To reduce the risk of
serious personal injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook. ONLY hang
tool’s belt hook from a work belt.
WARNING: To reduce the risk of
serious personal injury, ensure the
screw holding the belt hook is secure.
IMPORTANT: When attaching or replacing the
belt hook or bit clip, use only the screw (h) that is
provided. Be sure to securely tighten the screw.
The belt hook (g) and bit clip (i) can be be attached
to either side of the tool using only the screw (h)
provided, to accommodate left- or right- handed
users. If the hook or bit clip is not desired at all, it
can be removed from the tool.
To move belt hook or bit clip, remove the screw
(h) that holds it in place then reassemble on the
opposite side. Be sure to securely tighten the screw.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCD735 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCD735 T 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DCD735 T 1

DeWalt DCD735 T 1 Additional guide - Polish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info