549026
10
Zoom out
Zoom in
Previous page
1/40
Next page
10
ENGLISH
Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock.
Removing
the battery pack will not reduce this risk.
NEVER
attempt to connect 2 chargers
together.
The charger is designed to operate on
standard 230V household electrical power.
Do not attempt to use it on any other
voltage.
This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB100 and DCB105 chargers accept 10.8 V
Li-Ion batteries.
These chargers require no adjustment and are
designed to be as easy as possible to operate.
Charging Procedure (fig. 2)
1.
Plug the charger (j) into an appropriate outlet
before inserting battery pack.
2. Insert the battery pack (g) into the charger. The
red (charging) light will blink continuously
indicating that the charging process has
started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE:
To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.
Charging Process
Refer the table below for the state of charge of the
battery pack.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot or
too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
Li-Ion BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic
Protection System that will protect the battery against
overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
Important Safety Instructions for
all Battery Packs
When ordering replacement battery packs, be sure to
include catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
READ ALL INSTRUCTIONS
Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Inserting or
removing the battery from the charger may
ignite the dust or fumes.
Never force battery pack into charger. Do
not modify battery pack in any way to fit into
a non-compatible charger as battery pack
may rupture causing serious personal injury.
Charge the battery packs only in DEWALT
chargers.
DO NOT
splash or immerse in water or other
liquids.
Do not store or use the tool and battery pack
in locations where the temperature may
reach or exceed 40 ˚C (105 ˚F) (such as
outside sheds or metal buildings in
summer).
WARNING: Never attempt to open the
battery pack for any reason. If battery pack
case is cracked or damaged, do not insert
into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or
charger that has received a sharp blow,
been dropped, run over or damaged in any
way (i.e., pierced with a nail, hit with a
hammer, stepped on). Electric shock or
electrocution may result. Damaged battery
packs should be returned to service centre
for recycling.
charging
– – – –
fully charged
–––––––––––
hot/cold pack delay
–– – –– –
replace battery pack
•••••••••••
State of charge
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCD710 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCD710 T 1 in the language / languages: English, French as an attachment in your email.

The manual is 4,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DCD710 T 1

DeWalt DCD710 T 1 User Manual - English, German, Dutch, Danish, French, Italian - 168 pages

DeWalt DCD710 T 1 Additional guide - Polish - 20 pages

DeWalt DCD710 T 1 User Manual - Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info